FUNCTIONS OF THE RADIO RECEIVER ASTRO 43 EXTERNAL:
the Dip-Switches in the transmitters are only to encode the user's code, no function can be made able by them
Memorizing one radio channel: Dip-Switch 5= ON
(procedure to memorize the single transmitter buttons in the receiver):
- Transmitter: open the casing and set the user's code by means of the internal Dip-Switches (Pic.3), record it down to prevent forgetting it, and re-assemble the unit.
- Set to
ON
one of the
Dip-Switches 1, 2, 3 or 4
in the receiver corresponding to the channel to memorize: the channel is activated by fitting the relay module, either NO or NC in
the receiver connector (Pic.1)
- Press and hold a transmitter button (Pic.2), the receiver learns the signal and the red led flashes to confirm memorizing:
each pulse with the transmitter emits a signal that closes the relay NO contact (or opens it, if the relay is NC) in the receiver output, corresponding to the memorized channel.
-
Important:
once this operation is finished set all the Dip-switches on to OFF. The receiver led flashes 5 times to confirm.
N.W.
In order to match all the radio channels with the respective transmitter buttons by a single operation (button 1 with channel 1, button 2 with channel 2, and so on.) set the
Dip-Switches 1, 2, 3, 4 and 5 = ON,
carry on the momorizing operation as before, by pressing and holding any one button of the transmitter until the led flashes 1 time.
Once the operation is finished set all the Dip-switches on to OFF. The receiver led flashes 5 times to confirm.
Deleting one transmitter: Dip-Switch 6= ON
(the memory does not receive any signal from that transmitter any longer, but the transmitter code remains in the memory)
- Press any one button of the transmitter to be deleted (previously memorized) (Pic.2): the led flashes 1 time to confirm that the signal is received
- Set on to
OFF
the
Dip-Switch 6
: only at this stage, the radio receiver deletes the transmitter from the memory, and the led flashes 6 times to confirm the operation as accomplished
-
Important:
once the operation is finished, set all the Dip-Switches on to OFF. in order to delete more transmitters, repeate the entire operation
Bistable Output: Dip-Switch 7= ON,
(first, it is necessary to memorize at least one transmitter button): the first pulse from the transmitter enables the relay, whereas the second pulse
from the same transmitter button disables it (step-by-step function).
- Set to
ON
one of the
Dip-Switches 1, 2, 3 or 4
corresponding to the radio channel required to be used as bistable mode and to the transmitter button as previously memorized
- Press the transmitter button required to operate on bistable mode (Pic.2)
-
Important:
once the operation is finished set all the Dip-Switches to OFF, the led in the receiver flashes 7 times to confirm the accomplished operation
Timer 1:
Dip-Switch 8= ON,
(first, it is necessary to memorize the transmitter button by means of which the function is carried out):
on pulsing the transmitter button, the output of the selected channel is activated for a time as pre-set, on expiring of which, it is
automatically deactivated
- Set to
ON
one of the
Dip-Switches 1, 2, 3 or 4
corresponding to the radio channel required to be used as mode timer 1
- Press the button 1 of the transmitter (Pic.2) as many times as the minutes required to be memorized (max 15 minutes)
- Press the button 2 of the transmitter (Pic.2) as many times as the seconds required to be memorized
NW:
After each pressing of the buttons, wait for the led to go off as a confirmation that the time has been memorized.
-
Once the operation is finished, set all the Dip-Switches to OFF, the led in the receiver flashes as many times as follows:
long flashes as the minutes, short flashes as the seconds. After a short pause, the receiver led flashes 8 times to confirm.
On operating phase, a pulse to the receiver from the transmitter button on mode Timer 1 (superior to 3 seconds), disables the output and stops the operation.
Timer 2:
Dip-Switch 9= ON,
(first, select and memorize the transmitter button by means of which this function is carried out):
a pulse from the transmitter activates the selected channel output for 200ms, after the time as pre-set, a second pulse
is released for another 200ms
- Set to
ON
one of the
Dip-Switches 1, 2, 3 or 4
corresponding to the radio channel to be used as mode timer 2
- Press the button 1 of the transmitter (Pic.2) as many times as the minutes required to be memorized (max 15 minutes)
- Press the button 2 of the transmitter (Pic.2) as many times as the seconds required to be memorized
NW:
After each pressing of the buttons, wait for the led to go off as a confirmation that the time has been memorized
-
Once the operation is finished, set all the Dip-Switches to OFF, the led in the receiver flashes as many times as follows:
long flashes as the minutes, short flashes as the seconds. After a short pause, the receiver led flashes 9 times to confirm.
On operating phase, a pulse to the receiver from the transmitter button on mode Timer 2 (superior to 3 seconds), gives out the 2nd pulse and stops the operation.
Deleting the total memory: Dip-Switch 10= ON,
the memory of the receiver is deleted in total
- Press any one button of the transmitter, provided it is already in the memory (Pic.2), for at least 5 seconds. The red led of the receiver stays on until the operation is finished.
-
Important:
Once the operation is finished, set all the Dip-Switches to OFF, the led in the receiver flashes 10 times to confirm the operation is accomplished
Set the outputs back to Standard mode: Dip-Switch 7= ON - Dip-Switch 8= ON - Dip-Switch 9= ON,
the single channels are kept in the memory (but all previous settings such
as Bistable, Timer T1 and Timer T2 modes are cancelled)
- Set to
ON
the
Dip-Switch
corresponding to the channel to be set back to Standard Mode.
- Press any one button of the transmitter, provided it is already in the memory (Pic.2), for at least 5 seconds. The red led in the receiver flashes once to confirm.
-
Important:
Once the operation is finished, set all the Dip-Switches to OFF, the led in the receiver flashes 3 times to confirm the operation is accomplished
DIP-SWITCHES ONLY IN THE RADIO RECEIVER ASTRO 43 EXTERNAL
Dip 1
= ON Operates
Relay 1 (Channel 1)
Dip 2
= ON Operates
Relay 2 (Channel 2)
Dip 3
= ON Operates
Relay 3 (Channel 3)
Dip 4
= ON Operates
Relay 4 (Channel 4)
Dip 5
= ON enables
memorization of the radio channels
Dip 6
= ON enables
delete one transmitter only
Dip 7
= ON enables the function
Bistable
Dip 8
= ON enables the function
Timer T1
(1sec ÷ 15min)
Dip 9
= ON enables the function
Timer T2
(1sec ÷ 15min)
Dip10
= ON enables the function
delete all memory
RADIO RECEIVER 433.92MHz:
self-learning, for external application
to operate with a 433.92MHz radio signal
Please note:
do not expose the receiver to electro-magnetic or
heat sources
Technical specifications:
Working frequency
433.92MHz± 75KHz
Intermediate frequency value
500 KHz
Stray emission max.power
2 nW
Aerial impedance value
50 Ohm
Sensitivity
1.5 µV
DC and AC power supply
12÷24V dc and ac
Absorption
20 mA ac
Working temperature
-10°C÷+55°C
Safety delay time
150msec
Relay contact rating
0.5A - 125V ac
IP standards
IP53
Distance range
120 metres
External
radio channels
4
Number of transmitters in the memory
800
IMPORTANT: to have an output available with
the radio receiver terminals, all the Dip-
Switches in it must be set on to OFF
!
Astro 43 Small
Button 1
Button 2
Button 1
Button 2
Button 1
Button 2
Button 3
Button 4
Dip -Switches only for encoding,
no function can be made able
by them
12V
+
-
+
-
Dip -Switches only for
encoding,
no function can
be made able by them
Pic. 3
Pic. 2
12V
Astro 43
91
73
27
Drwg.
5486
meccanica
FADINI
GB
INSTRUCTIONS OF THE RADIO RECEIVER
ASTRO 43
M.Q.B.
EXTERNAL
SELF-LEARNING, MULTIFUNCTIONS AVAILABLE
EXTERNAL
Self-learning
Astro 43
M.Q.B.
code 4327
- EXTERNAL
Directive
2003/108/EC
Disposal of electric and
electronic material
DO NOT DISPOSE OF AS NORMAL WASTE.
HARMFUL FOR THE ENVIRONMENT
GB
ON
OFF
OFF
Timer 1
Signal output
Pulse from the
transmitter
ON
OFF
OFF
Timer 2
200ms output
Pulse from the
transmitter
Relay 1
(standard)= enables
Channel 1
Relay 2
= enables
Channel 2
Relay 3
= enables
Channel 3
Relay 4
= enables
Channel 4
1°
2° 3°
4°
Power supply
12V
or
24V dc/ac
from control panel Elpro range
Modules
(non standard)
NO
or
NC
to enable the radio channels:
Dip -Switches to select functions
Aerial
Birio A8 with
cable RG58
NO modules
aerial RG 58
1 2 3 4 5 6 7 8 9 10 11 12
1°
24V
2°
3°
4°
Strip to select power
supply either
12V
or
24V dc/ac
24V dc/ac
12V dc/ac
Pic. 1
Astro
Removable
memory
Red led
