Factory Buys Direct PFS FDF150T страница 15 Скачать руководство пользователя

Страница: 15 / 32

www.factorybuysdirect.com

200200-01C

Figure 11 - Gas Connection

* Purchase the optional CSA design-certified equipment

shutoff valve from your dealer.

The installer must supply an external regula-

tor. The external regulator will reduce incom-

ing gas pressure. You must reduce incoming

gas pressure to between 11" and 14" of water.

If you do not reduce incoming gas pressure,

heater regulator damage could occur. Install

external regulator with the vent pointing down

as shown in Figure 12. Pointing the vent down

protects it from freezing rain or sleet.

Figure 12 - External Regulator

with Vent Pointing Down

Figure 13 - Gas Regulator Location and

Gas Line Access into Stove Cabinet

External

Regulator with

Vent Pointing

Down

Propane

Supply Tank

Equipment

Shutoff Valve

Ground

Joint Union

3/8" NPT

Pipe Nipple

Tee Joint

Reducer

Bushing to

1/8" NPT

Plug Tap

Test Gauge

Connection*

Sediment

Trap

Tee Joint

Pipe Nipple

Gap

3" Minimum

Gas Regulator

Inlet Connector

Install sediment trap in supply line as shown

in Figure 11. Place sediment trap where it is

within reach for cleaning. Place sediment trap

where trapped matter is not likely to freeze.

A sediment trap traps moisture and contami-

nants. This keeps them from going into heater

controls. If sediment trap is not installed or is

installed wrong, heater may not run properly.

Natural Gas

From Gas Meter

(5" W.C.** to 9"

W.C. Pressure)

Propane

From External

Regulator

(11" W.C.**

to 14" W.C.

Pressure)

INSTALLATION

Содержание PFS FDF150T

































Результаты поиска

Содержание PFS FDF150T

Отзывы:

Похожие инструкции для PFS FDF150T

Бренды по названию

Популярные бренды

Factory Buys Direct PFS FDF150T, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание PFS FDF150T

Отзывы:

Похожие инструкции для PFS FDF150T

Бренды по названию

Популярные бренды