Fabtech FT22176i Скачать руководство пользователя страница 11

Страница: 11 / 17

38. Locate the factory knuckle and remove the 4WD actuator

and hub assembly.

SEE FIGURES 37-38 NOTE: REFER

TO FIGURE 61 ON THE LAST PAGE FOR SPECIFIC
INSTRUCTIONS ON DISASSEMBLY AND ASSEMBLY
OF THE 4WD ACTUACTOR.

39. Locate the Fabtech driver side spindle (FT30617D) and

install the factory hub. Torque the four 14mm bolts to 160
ft- lbs.

SEE FIGURE 39

40. Re-install the 4WD actuator using the 3 factory bolts.

Torque to 29 ft-lbs.

SEE FIGURE 40

41. Install the Fabtech knuckle onto the upper and lower

control arms.

NOTE: Install the supplied spacer on the

lower ball joint.

Torque the upper ball joint to 85 ft-lbs

and the lower ball joint to 110 ft-lbs.

SEE FIGURE 41-42

11 of 17

FIGURE 37 - STEP 38

FIGURE 38 - STEP 38

FIGURE 39 - STEP 39

FIGURE 41 - STEP 41

FIGURE 40 - STEP 40

FIGURE 42 - STEP 41

Содержание FT22176i


















Результаты поиска

Содержание FT22176i

Отзывы:

Похожие инструкции для FT22176i

Бренды по названию

Популярные бренды

Fabtech FT22176i, Руководство по установке

Результаты поиска

Содержание FT22176i

Отзывы:

Похожие инструкции для FT22176i

Бренды по названию

Популярные бренды