manualshive.com logo in svg

FAAC Estate Slide, Инструкция по эксплуатации

Поделиться
Скачать
FAAC Estate Slide Скачать руководство пользователя страница 21

8.1 

Control Board LED Lights 

- The control board LED lights are located above their respec-

tive terminals that they represent. (With exception of ALIM, power supply light) The LED lights 
are a quick way of verifying necessary connections are made. Below is a chart of their interpreta-
tions. 

LED Lights & Operational Displays 

LED 

ON 

OFF 

ALIM 

Powers supply by transformer 

Power supply by battery or no power 

FCC 

Closing limit switch - not tripped 

Closing limit switch - tripped 

FCA  

Opening limit switch - not tripped 

Opening limit switch - tripped 

STOP 

Stop command - not activated 

Stop command - activated 

FSW CL 

Closing safety device - not tripped 

Closing safety device - tripped 

FSW OP 

Opening safety device - not tripped 

Opening safety device - tripped 

During idle for dual gate openers, all LED lights should be on. 
 
If not using safety devices , you must jump STOP, FSW CL and FSW OP to COM in order 
for the gate opener to function. 

Standard Operation Display 

- 

This is when the gate opener is not in parameter setting 

mode or programming mode. LED displays DS1 and DS2 will show the following: 

Gate Status 

Gate At Rest in Closed Position 

Gate Opening or Gate Open when Auto Close is OFF 

Gate open in pause status 
(Only with automatic re-close enabled - Parameter c) 

Gate Closing 

Содержание Estate Slide


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды