background image

8

7.  START-UP 

When you have carried out all the electrical connections, locked 

the operator, and checked that the door cannot be moved by 

hand, power up the system.

If the operator is supplied with a winch, fix - in the immediate vicinity 

of the chain - the sticker indicating the traction directions for the 

opening and closing manual manoeuvres.

7.1  541 3ph WITH 844T EQUIPMENT

Program the unit, following the instructions of the 844T unit.

  6.  ELECTRICAL SYSTEM

ATTENTION: Before attempting any work on the board (connections, 

maintenance), always turn off power.

The specifications of the electrical system are included in the chap

-

ter “Warnings for the installer”. Always separate power cables from 

control cables.

The 541 3ph operator is supplied with an on-board inter-connection 

board.

6.1  CONNECTIONS OF 844T ELECTRONIC EQUIPMENT

Lay the raceways according to the instructions in figure 4.

Make the connections between the 844T unit and the 541D inter-

connection board, installed on the operator, following the diagram 

in figure 17.

A STOP push-button, if any, must be located in series with respect 

to the connection between the STOP input of 844T and the SAFETY 

of the 541D INTERFACE.

For wiring, and for programming the 844T, refer to the instructions 

for the unit.

 

Fig. 17

8.  MAINTENANCE

Maintenance: check at least every 6 months the efficiency of the 

system, particularly the efficiency of the safety devices (including, 

where  foreseen,  the  operator  thrust  force)  and  of  the  release 

devices.

9.   REPAIRS

For repairs contact an authorised FAAC Repair Centre.

  Release knob (red)

  Locking knob (green)

Fig. 15

Fig. 16

Содержание 541 3ph













Отзывы: