![background image](http://html1.mh-extra.com/html/faac/452-mps/452-mps_manual_3100378008.webp)
7
during the learning procedure, the safety devices
are disabled! Therefore any transit must be avoided
in the leaf movement area when this operation is
carried out.
6. START-UP
6.. LED CHECK
The table below shows the status of the LEDs in relation to to the status
of the inputs.
Note the following:
L
ed
Lighted
= closed contact
L
ed
off
= open contact
Check the state of the LEDs as per Table.
Operation of the status signalling LEDs
Opening/closing time is established by a learning procedure which can
be effected in two different ways depending on the type of system.
Simple learning
makes it possible to effect a single rapid operation
to supply work times to the board, without using deceleration. It is not
recommended if the speeds of the leaves differ considerably from each
other (different operators, different opening dimensions or angles).
Complete learning
makes it possible to exploit all functions of the
equipment, and thus program different work times for each leaf, and
also opening and closing deceleration.
- SIMPLE LEARNING:
Check if the leaves are closed, and then press F push-button for one
second: DL10 LED begins flashing and the leaves begin the opening
movement.
Wait for the leaf to reach the opening stop limit and then supply an OPEN
A pulse (with the radio control or with the key controlled push-button) to
stop the movement: the leaves stop and the DL10 LED stops flashing.
6.. ROTATION DIRECTION AND FORCE CHECK
1) Program the microswitches of the control board according
to need, as shown in Chapter 5.
2) Cut power to the electronic control equipment.
3) Release the operators and manually move the gate to the
mid-point of the opening angle.
4) Re-lock the operators.
5) Restore power.
6) Send and opening command on the OPEN A input (fig.2)
and check if the gate leaves are being commanded to
open.
. If the first OPEN A pulse commands a closing, cut power
and change over the phases of the electric motor (brown and
black wires) on the terminal board.
7) Check power setting of the motors and, if necessary, modify
it (see Chapter 5.1).
8) Stop leaf movement with a STOP command.
9) Release the operators, close the leaves and re-lock the
operators.
The status of the LEDs while the gate is at rest are shown
in bold.
Furthermore, the DL10 LED is on the board and functions as
detailed in the following table:
LEDs
LIGHTED
OFF
OP_A
Command activated
Command inactive
OP_B
Command activated
Command inactive
STOP
Command inactive
Command activated
FSWCL
Safety devices disengaged
Safety devices engaged
FSWOP
Safety devices disengaged
Safety devices engaged
DL10
Gate closed at rest:
OFF
Gate moving or on
pause:
like indicator-light
Time learning:
flashes rapidly
6.3. LEARNING OF OPERATING TIMES
The procedure has ended and the gate is ready to operate.
Next pulse closes leaves and they stop on automaticaly reaching closed
position.
- ADVANCED COMPLETE LEARNING:
Check if the leaves are closed, and then press F push-button for more than
3 seconds: DL10 LED begins flashing and the leaf 1 begins the opening
movement. The following functions can be commanded by the OPEN
A pulses (by radio control or key controlled push-button):
1° OPEN - Deceleration at opening of leaf 1
2° OPEN - Leaf 1 stops at opening and leaf 2 begins its opening
movement
3° OPEN - Deceleration at opening of leaf 2
4° OPEN - Leaf 2 stops at opening and immediately begins its
closing movement
5° OPEN - Deceleration at closing of leaf 2
6° OPEN - Leaf 2 stops at closing and leaf 1 begins its closing
movement
7° OPEN - Deceleration at closing of leaf 1
8° OPEN - Leaf 1 stops at closing
The DL10 LED stops flashing and the gate is ready for normal
operation.
Notes:
•If you wish to eliminate deceleration in certain stages, wait
for the leaf to reach its stop-limit and supply 2 consecutive
Open pulses (by 1 second).
•If only one leaf is present, the entire sequence must
nevertheless be effected. When the leaf has finished opening,
supply 5 Open pulses until the leaf begins to close, and then
resume normal operation.
•It wind effected areas it is best to allow 2 second after the
leaf reaches open stop befor supplying Open A to ensure
full closing.
•Use of slow-down is not recommended for condominium
entries.
•If, during closing / opening, the cycle stops for more con-
secutive times, the leaf could not reach the limit stop with
slow-down. At the first complete cycle without interruptions,
the system recognizes the limit stops and carries out again
the programmed slow-downs.
6.4. PRE-FLASHING
If you wish to increase the equipment's safety level, you can
activate the pre-flashing function which enables the flashing lamp
to go on 5 seconds before the leaf starts to move.
Pre-flashing activation procedure:
1 - check if the gate is closed
2 - open and keep open the
Stop
contact
3 - check if the
DL10
LED is OFF (if lighted, pre-flashing is
already active)
4 - briefly press the
F
push-button and check if the
DL10
LED
lights up.
5 - close the
Stop
contact (DL10 goes OFF).
Procedure for disabling the function:
1 - check if the gate is closed
2 - open and keep open the
Stop
contact
3 - check if the
DL10
LED is lighted (if OFF, pre-flashing is
already disabled)
4 - briefly press the
F
push-button and check if the
DL10
LED
is OFF.
5 - close the
Stop
contact
7. AUTOMATED SYSTEM TEST
When you have finished programming, check if the system is
operating correctly.
Most important of all, check if the force is adequately adjusted and
if the safety devices are operating correctly.
ENGLISH
Содержание 452 MPS
Страница 1: ...452 MPS...