F5 BIG-IP 8950 Скачать руководство пользователя страница 10

Страница: 10 / 56

Figure 3: The LCD panel and control buttons

About LCD menus

There are three menus on the LCD panel. You can configure the display options to meet your needs.

LCD config menu

You can use the LCD config menu to adjust the display properties of the LCD panel.

Description

Option

Specifies an LCD screen backlighting option. Select from the
following options:

Backlight

•

ON enables the backlight.

•

GRAY enables the software to specify when the backlight is
illuminated.

•

OFF disables the backlight.

Sets the contrast of the LCD.

Contrast

Adjusts LCD backlight brightness.

On Brightness

Controls the brightness of the LCD when the backlight is off.

Off Brightness

Screens menu

You can use the Screens menu to specify the information that is displayed on the default screens.

Description

Option

Displays the date and time.

DateScreen

Displays the information screen menu.

InfoScreen

Displays the MAC addresses on the unit.

MACscreen

Displays system information.

SysinfoScreen

Displays the number of authentication requests being processed.

TMMAuthScreen

Displays the CPU usage percentage.

TMMCPUScreen

Displays the memory usage.

TMMMemoryScreen

Displays simple statistics, such as bytes and packets in and out of
the system.

TMMStatScreen

Displays product version information.

VersionScreen

About the 8950 platform

Содержание BIG-IP 8950

























































Результаты поиска

Содержание BIG-IP 8950

Отзывы:

Похожие инструкции для BIG-IP 8950

Бренды по названию

Популярные бренды

F5 BIG-IP 8950, Руководство по платформе

Результаты поиска

Содержание BIG-IP 8950

Отзывы:

Похожие инструкции для BIG-IP 8950

Бренды по названию

Популярные бренды