![background image](http://html1.mh-extra.com/html/f-f-group/rs-1050-e-plus/rs-1050-e-plus_original-instructions-manual_3097191006.webp)
| English
6
Meaning of crossed - out wheeled dustbin:
Do not dispose of electrical appliances as un-
sorted municipal waste, use separate collec-
tion facilities. Contact your local government
for information regarding the collection
systems available. If electrical appliances are
disposed of in landfills or dumps, hazardous
substances can leak into the groundwater
and get into the food chain, damaging your
health and well-being.
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardized documents: EN 60745-1, EN 60745-2-11,
EN 61000-3-2, EN 61000-3-3, EN 55014-1, EN 55014-
2 in accordance with the provisions of the directives
2006/42/EC, 2014/30/EU
Technical file at:
FF GROUP TOOL INDUSTRIES S.A.,
19300, Aspropyrgos-Greece
Loudovikos Tsirigiotis
Operations & Engineering
FF GROUP TOOL INDUSTRIES S.A.,
19300 Aspropyrgos-Greece. 19/01/2018
the work.
f
f
In general, coarser blades are for wood, plastics , and
composites, and finer blades are for cutting metal, chat
-
tering or vibration may indicate you need fine blade or
higher speed, if the blade overheats or clogs, it may in
-
dicate you need a coarser blade when they become dull.
Dull blades will produce poor results and may overheat
the saw.
Plunge cutting
Clearly mark the line of cut, from a convenient starting
point within the cut out area, place the tip of the blade
over that point with saw parallel to the line of cut, slow
-
ing lower the saw until the button edge of the shoe
rests on the work piece and the blade not touching
the work piece, start the saw and allow it to attain full
speed. With the saw resting on the shoe, slowly tilt the
saw forward to lower the blade onto the cut line. Con-
tinue this motion until the saw blade is perpendicular
to the work piece.
Metal cutting
Blades specifically designated for cutting metals must
be used for this purpose. You may use light oil as a cool-
ant when cutting metal, this will prevent overheating
of the blade, help the blade cut faster, and promote
longer blade life.
Cleaning and maintenance
The machine does not require any special mainte
-
nance. Regularly clean the ventilation slots.
CAUTION:
Do not use cleaning agents to clean the
plastic parts of the tool. A mild detergent on a damp
cloth is recommended. Water must never come into
contact with the tool.
Replacement of the Carbon Brushes
For safety reasons, the machine automatically switch-
es off if the carbon brushes are so worn out that they
no longer have contact with the motor. In that case,
the carbon brushes must be replaced by a pair similar
carbon brush available through the after-sales service
organization or qualified professional person. Loosen
the carbon brush cover anti-clockwise with using a
screwdriver, open the cover and remove the carbon
brushes. If they are 6 mm or less then they must both
be replaced. Fit new carbon brushes and change it.
CAUTION:
The brushes must always be replaced in
pairs.
CAUTION:
Always disconnect the machine from the
power supply before removing any electrical covers.
Conforms to relevant safety standards
To reduce the risk of injury, the user
must read and understand this manual
before using this product.
Wear ear protectors. Exposure to noise
can cause hearing loss.
Wear eye protection.
Wear respiratory protection.
Double insulation
Содержание RS 1050 E PLUS
