F.F. Group 43 283, Оригинальное руководство пользователя

Страница: 9 / 48

DS 1010 PLUS English | 9
www.ffgroup-tools.com
No-load speed min -1 1.000-2.350
Pad diameter mm 210
Sanding sheet size mm 225
Weight kg 3,25
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
Sound pressure level dB(A) 83,4
Sound power level dB(A) 94,4
Uncertainty K dB 3
Vibration total values a
h
(triax vector sum) and
uncertainty K determined according to
EN 60745-1
Vibration level max:
a
h ,HD
m/s
2
1,745
K m/s
2
1,5
IDENTIFICATION
1. On/off switch
2. Pad cover segment
3. Flexible hose + vacuum cleaner adapter Ø 57
mm
4. Backing pad (VELCRO)
5. Sanding disc
6. Sanding speed selection wheel
7. Vacuum cleaner adapter Ø 47 mm
8. Vacuum cleaner adapter Ø 35 mm
9. Double-ended screwdriver
10. Hex key
11. Safety button for On/Off switch
REPLACEMENT OF SANDING PAPER
Backing pads 4
Never run the tool without backing pad 4
ƒ
Replace damaged backing pads immediately
(loosen/fasten pad screw with hex key 10).
ƒ
Unplug tool before removing/mounting back-
ing pads.
Mounting sanding discs 5
ƒ
Simply press sanding disc 5 onto backing pad with
perforation in sanding disc corresponding with
perforation in backing pad. If necessary, clean
backing pad first
ƒ
The dust suction requires the use of perforat-
ed sanding discs.
REPLACEMENT OF GRINDING DISC STUCK
The output shaft is inserted into the adhesive disc
center with six angle wrench clockwise rotation
angle in the six-hex, and at the same time, the
hands hold the adhesive disc grinding, grinding
disc can be remove adhesive.
SPEED ADUSTMENT
The grinding of the grinding disc rotation speed
can be adjusted according to different conditions
and grinding quality requirements.
The Drywall Sander is equipped with a variable
speed control. The speed is adjusted by turning
the control knob. The control knob is numbered
"MIN" through "MAX" with "MIN" being the slow-
est speed (Approximately 1000 RPM) and "MAX"
being the fastest speed (approximately 2350
RPM).
Use the higher speed settings for fast stock re-
moval. Use the lower speed selling to reduce re-
moval rate for more precise control.
ANGLE GRINDING
In order to do side grinding work, take off the
front part of plastic disc with screw driver.
TO START AND STOP DRYWALL SANDER
Make sure power circuit voltage is the same as
shown on the specification plate on the sander,
and that the sander switch is OFF. Connect sander
to power circuit.
To start the sander: Press the safety button and
press the ON/OFF switch.
To stop the sander: Release the ON/OFF switch.
HOLDING AND GUIDING THE TOOL
f
Always hold the tool firmly with both hands.
f
While working, always hold the tool at the grip
area.
f
Guide the tool parallel to the working surface and
move it in circles or in a cross pattern
f
Do not apply too much pressure on the tool; let
the sanding surface do the work for you
f
Do not tilt the tool in order to avoid unwanted
sanding marks.
f
Keep ventilation slots uncovered.
SANDING
f
The amount of material removed is determined
by the speed of the sanding disc and the grit size
used.
f
The speed of the sanding disc decreases relative
to the pressure applied to the tool.
MAINTENANCE
f
Keep tools clean, clean up debris and dust.
f
Always check the power cable, plug, switch, so
that the tools is in good condition.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of dispos -
ing as waste. Machine, accessories and
packaging should be sorted for envi-
ronment - friendly recycling. The plastic
components are labeled for categorized
recycling.