Ezgo 611103 Скачать руководство пользователя страница 162

Страница: 162 / 186

Page O-8

TROUBLESHOOTING AND DIAGNOSTICS

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.

25106

Reverse Alarm Test

Failed

1. Reverse warning alarm

failed at startup check. The

controller tests for a completed

reverse warning alarm circuit.

1. Turn key switch to ’OFF’ and unplug 23 pin

connector from controller.
2. Check the reverse warning alarm for a

shorted condition, less than 0.1 ohms, by

measuring between pin 10 and pin 13 with

the Run/Tow switch in the ’TOW’ position. If

test is greater than 0.1 ohms see

ACTION 1

3. Turn key switch to ’R’ and verify voltage to

the reverse warning alarm is 48 volts, if not

then see

ACTION 2

1. Replace reverse warn-

ing alarm.
2. Replace wiring
3. Replace controller

25107

Mechanical Brake

Failed

1. Parking brake failed to pre-

vent motor from rotating during

the park brake startup test.

NOTE: this fault may occur if

the key switch is turned to

’OFF’ and then to ’ON’ quickly

while the vehicle is moving.

1. Turn key switch to ’OFF’ and try to push

the vehicle, it should NOT move.
2. Unplug the harness from the motor brake.
3. Verify brake coil resistance is 27 ±3 ohms,

if out of range see

ACTION 1

4. Verify that friction disk is in alignment, if

not aligned see

ACTION 2

5. Turn key switch to ’ON’ and with the ’Run/

Tow’ switch to ’RUN’ and try to push the car.

1. Replace motor brake.
2. Realign the friction disk.
3. Replace the controller.

25108

Brake Sensor Error

Brake position sensor input is

out of range, there are three

conditions which can cause

this error.
1. Low sensor voltage, less

than 0.35 volts.
2. High sensor voltage, greater

than 4.8 volts.
3. Sensor voltage greater than

0.85 volts when brake switch

closes.

1. Verify that the 5 volt out put range is 5 ±0.1

volts.
2. Turn key switch to ’N’ and check that the

accelerator pedal is in the upright position.
3. Verify that accelerator pedal arm is in con-

tact with the rubber bumper, if not in contact

with bumper see

ACTION 1

4. Verify the throttle sensor voltage is

between 0.35 volts and 4.8 volts. If not in

range see

ACTION 2

5. Verify the throttle sensor voltage is less

than or equal to 0.85 volts when throttle

switch closes. If greater than 0.85 volts see

ACTION 3

6. Verify other 5 volt supply devices; motor

encoder, resistor module and brake sensor.

1. Remove obstruction.
2. Replace throttle sensor.
3. Replace throttle switch.
4. Repair or replace bad

device.

33024

CAN Timeout

1. This error occurs when the

controller and the handled

devices stop communicating.

1. Check for a loose handheld connection or

a damaged handheld. Replace the CAN Bus

plug (run plug).

1. Cycle the key switch

(turn it off then back on).
2. Depress accelerator

pedal, release and

depress again.

Warning Drive Fault

1. Indicates the current error is

the result of a condition internal

to the controller. The message

can appear in combination with

one of the above error mes-

sages.

1. Trouble shoot according to the controller

error message displayed.

1. Replace motor control-

ler

CODE

DESCRIPTION

POSSIBLE CAUSES

DIAGNOSTIC STEP

ACTION (post diagnos-

tics)

Содержание 611103



























































































































































































Результаты поиска

Содержание 611103

Отзывы:

Похожие инструкции для 611103

Бренды по названию

Популярные бренды

Ezgo 611103, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание 611103

Отзывы:

Похожие инструкции для 611103

Бренды по названию

Популярные бренды