Ezee-On 4600 DISC Скачать руководство пользователя страница 37

Страница: 37 / 78

Page 36

ASSEMBLY INSTRUCTIONS CONTINUED:

b) See Fig. 31. Position each scraper assembly on REAR side of it’s gang with scraper placed against concave side of blades. Fasten scraper assembly

to gang beam with ONE (1) scraper mount plate for each bearing hanger in the gang. Position outer scraper mount plates as close as possible to the

end of the scraper bar. Position the inner scraper mount plate(s) close to a bearing hanger. Locate standard scraper mount plates on BOTTOM side

of gang beam and secure with (1) 3/4" x 6" (19.0mm x 152.4mm) U-Bolt c/w nuts and lockwashers as shown in Detail “E”. Place scraper bar

assembly on TOP of scraper mount plates and secure scraper bar to plates with one (1) 5/8" x 2" (15.7mm x 50.8mm) U-Bolts c/w nuts and

lockwashers.

NOTE: In some cases the standard scraper mount plate, shown in Detail “E”, can not be installed between frame and a bearing hanger.

In these instances an offset scraper mount is provided. This mount plate is placed on top of the gang beam, as shown in Detail “D”,

allowing clearance for installation. All Models are supplied with six (6) offset mounts. If they are not used for tight locations, use

them in normal locations.

34.

IMPORTANT:

WHEN RAISING WINGS FOR TRANSPORT FOR FIRST TIME AFTER ADJUSTING GANGS, RAISE WINGS SLOWLY MAKING SURE WING GANGS

CLEAR CENTRE FRAME GANGS.

35. See Fig. 32. Adjust scraper bar, arrow 1, and scrapers, arrow 2, of

each gang so that each scraper blade is in contact with disc blade.

IMPORTANT:

DISC WILL REQUIRE LESS HORSE POWER TO PULL

IF SCRAPERS ARE ADJUSTED PROPERLY.

CAUTION:

WHEN ATTACHING GANG ASSEMBLIES, WEAR

PROTECTIVE GLOVES TO HELP PREVENT INJURY

FROM CUTTING EDGES OF BLADES.

36. See Fig. 33. Level frames with main frame as follows:

a) Raise disc by extending rockshaft cylinders, be sure wing

rockshaft cylinders are fully extended.

b) Check position of the spindle mounting tube, arrow 1, (welded to

bottom of rockshaft wheel leg).This distance should be 23-1/2"

(596.9mm) from the bottom of wing frame to top of spindle

mounting tube.

c) If spindle mounting tube locatin is not correct, adjust length of

wing cylinder I-Bolt, arrow 2. Extending I-Bolt will move spindle

mount tube further away from bottom of frame while contracting

I-Bolt will move it closer.

d) After adjustments are complete, lock I-Bolt by tigtening rear nut,

arrow 3, against I-Bolt holder.

NOTE:

The above wheel leg settings are initial settings only. If wing gangs do not cut at same depth as main frame gangs, further wing cylinder

adjustment will be required.

IMPORTANT

BE SURE AXIS OF CLEVIS PIN IS HORIZONTAL AND CYLINDER PORTS ARE FACING UP. IF CYLINDER AND I-BOLT ARE NOT POSITIONED

PROPERLY, CYLINDER WILL NOT BE FREE TO PIVOT WHEN ACTIVATED CAUSING SERIOUS DAMAGE.

Содержание 4600 DISC















































































Результаты поиска

Содержание 4600 DISC

Отзывы:

Ezee-On 4600 DISC, Руководство пользователя, Страница: 37 / 78

Результаты поиска

Содержание 4600 DISC

Отзывы: