background image

 

 

12 

 

2. 

Press 

. When “OFF” begins  flashing, use 

to select the desired hour and minute to turn off the heater. 

Press 

at any time to clear the digits and shut down 

“OFF” timer.

 

 

3. 

Press 

again. When “18” begins flashing, use 

to select the desired temperature for Monday.

 

 

 

 

4. 

Press 

again. When 

“TUES” appears on the screen and “ON” begins flashing, use 

to select the desired 

hour and minute to turn on the heater for Tuesday.

 

 

5. 

Press 

again. When “OFF” begins flashing, use 

 

to select the desired hour and minute to turn off the 

heater for Tuesday.

 

 

6. 

Press 

again. When “18” begins flashing, use 

to select the desired temperature for Tuesday.

 

 

7. 

Repeat steps 1 to 6 to set the “ON/OFF” time and temperature for Wednesday, Thursday, Friday, 
Saturday, and Sunday.

 

 

8. 

Press 

or 

 to finish, ensuring to aim the remote control at the receiver located in the middle of the 

appliance. The appliance will 

“beep” once to confirm your settings have been saved successfully.

 

Open window  warning

 

If the room temperature decreases by 10 degrees within 3 minutes, the appliance will assume there is an open window 
nearby. In order to conserve energy, the heater will automatically switch from High Heat to Low Heat, or if the heater is 
already at Low Heat, it will turn off completely.

 

 

When switching from High Heat to Low Heat, the appliance will beep 3 times and the digital display will flash 

“88” 3 times 

before displaying the existing heating status.

 

 

When switching from Low Heat to Off, the appliance will beep 3 times and the digital display will flash 

“88” continuously.

 

 

To 

reset the heating function, see “operating remote control” section.

 

 
 
 
 

NOTICE 

When the heater is first turned on, a slight odor may be present. This is normal and 
won’t occur again unless the heater is un-used for a long period of time. 

 
 
 

NOTICE 

To improve operation, 

aim

 the remote control at the front of the fireplace. 

DO NOT 

press the buttons too quickly

. Give the unit time to respond to each command.  

Temperature Limiting Control 

This  heater  is  equipped  with  a  Temperature  Limiting  Control.  Should  the  heater  reach  an  unsafe 
temperature, the heater will automatically turn OFF. To reset:  

1.  Unplug the power cord from the outlet.  

2.  Turn the ON/OFF switch on the CONTROL PANEL to OFF. 

Wait 5 minutes.  

3.  Inspect the fire unit and make sure all vents are free from dust or lint. If they are clogged, use a 

vacuum to clean the vent areas. 

4.  With the POWER switch in the OFF position, plug the power cord back into the outlet. 

5.  If the problem continues, have your outlet and wiring inspected by a professional.

 

note:

 

If the temperature was previously set, those digits will be shown instead of 

“18”.

 

Содержание Celestial 600


















Отзывы: