Eyedro EB Series Скачать руководство пользователя страница 10

Страница: 10 / 45

PRODUCT GUIDE: EYEDRO ELECTRICITY MONITORING PRODUCTS

P a g e

HARDWARE INSTALLATION

DO NOT CONTINUE WITH THE INSTALLATION OF THE EYEDRO
ELECTRICITY MONITORING SYSTEM UNTIL YOU HAVE READ THE
SAFETY SECTION OF THIS GUIDE.

LOCATING THE ELECTRICAL SERVICE

The electricity panel is typically located in the garage or utility room of the building – although this is not
always the case. The below diagrams show two typical 120/240V split-phase (single-phase) electrical
service configurations:

SERVICE BOX AND DISTRIBUTION
PANEL

In some cases the service entrance wires, from
the utility company, feed into a box that is
isolated from the distribution panel.

In this particular configuration, current sensors
can be installed on the Line wires in either the
service entrance panel or distribution panel.

COMBINATION
SERVICE/DISTRIBUTION PANEL

In some cases the service entrance wires, from
the utility company, and main breaker are
integrated into a single main electrical panel.

In this particular configuration, current sensors
are installed on the Line wires between the main
breaker and the meter.

Main Breaker

Содержание EB Series














































Результаты поиска

Содержание EB Series

Отзывы:

Eyedro EB Series, Руководство по эксплуатации продукта, Страница: 10 / 45

Результаты поиска

Содержание EB Series

Отзывы: