2
Cabling and Mounting the XTP R HWP 201 4K
Rear panel connections
1.
Connect a shielded twisted pair cable between the XTP input connector on the receiver (see
figure 1
,
A
on
the previous page) and the XTP output connector on an XTP twisted pair transmitter or XTP matrix switcher.
ATTENTION:
Do not connect this connector to a computer data or telecommunications network.
The XTP R HWP 201 4K is compatible with shielded twisted pair (F/UTP, SF/UTP, and S/FTP) cables. Extron
recommends using the following practices to achieve full transmission distances up to 330 feet
(100 meters) and reduce transmission errors.
•
Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron recommends
24 AWG, solid conductor, STP cable with a minimum bandwidth of 400 MHz.
•
Terminate cables with shielded connectors to the TIA/EIA-T568B standard.
•
Limit the use of more than two pass-through points, which may include patch points, punch down
connectors, couplers, and power injectors. If these pass-through points are required, use shielded
couplers and punch down connectors.
NOTE:
When using shielded twisted pair cable in bundles or conduits, consider the following:
•
Do not exceed 40% fill capacity in conduits.
•
Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles.
•
Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
•
Separate twisted pair cables from AC power cables.
2.
Power the XTP R HWP 201 4K in one of the following methods:
•
Connect the provided external power supply to the 2-pole captive screw connector for local 12 V power (see
figure 1
,
B
).
•
Connect an XTP Power Injector to the XTP connection between the receiver and a locally powered XTP transmitter or XTP matrix switcher.
•
Connect the XTP R HWP 201 4K to an XTP matrix switcher and enable the remote power feature on the XTP matrix switcher.
Mounting the XTP R HWP 201 4K to the metal junction box or mud ring
1.
Using the provided screws, attach the XTP R HWP 201 4K to the mud ring or metal junction box through the inner screw holes (see
figure 2 or 3
on the previous page).
2.
Using the provided screws, attach the faceplate to the XTP R HWP 201 4K through the outer screw holes (see
figure 2 or 3
).
NOTE:
For configuration, control, and firmware upgrades, connect a host device to the USB mini-B connector before attaching the
faceplate (see
figure 1
,
G
, and see the
XTP R HWP 201 4K User Guide
for details).
Front Panel Connections
1.
Connect a host device or control LAN or WAN to the LAN RJ-45 connector for pass-through 10/100 Base-T
Ethernet communication (see
figure 1
,
C
). This is an Ethernet pass-through port.
2.
To pass bidirectional serial, infrared, or other control signals, connect a control device or controllable device
to the RS-232 and IR Over XTP connector (see
figure 1
,
D
). Wire the connector as shown to the right.
NOTE:
RS-232 and IR data can be transmitted simultaneously.
3.
Connect a balanced or unbalanced, stereo
or mono audio output device to the 3.5 mm,
5-pole captive screw connector (see
figure 1
,
E
) for 2-channel stereo analog audio. Wire the
connector as shown to the right.
4.
Connect a digital video display to the female
HDMI connector (see
figure 1
,
F
).
Configuration and Control
To configure the receiver, connect a host device to the front panel USB configuration port (see
figure 1
,
G
). On the host device, use the Extron
XTP software (recommended) or Simple Instruction Set (SIS
TM
) commands via Extron DataViewer (see the
XTP R HWP 201 4K User Guide
at
www.extron.com
for more information).
TIA/EIA-T568B
Pin Wire Color
1
White-orange
2
Orange
3
White-green
4
Blue
5
White-blue
6
Green
7
White-brown
8
Brown
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A
T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Tx/Rx
Pins
Tx Rx
Rx Tx
IR Device
RS-232 Device
G
G
Tx
Rx
G
OVER XTP
RS-232 IR
Tx
Rx
Do not tin
the wires!
Balanced Audio Output
Tip
Ring
Tip
Ring
Sleeves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
LR
© 2019 Extron Electronics — All rights reserved.
www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters:
Extron USA West, 1025 E. Ball Road, Anaheim, CA 92905, 800.633.9876
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide
on the Extron website.
68-2908-50 Rev. A
12 18