manualshive.com logo in svg

Extron electronics PVS 407D, Руководство пользователя

Поделиться
Скачать
Extron electronics PVS 407D Скачать руководство пользователя страница 12

B

 

Inputs 5 and 6

 (see 

figure 3 

on the previous page) — Connect up to two HDMI 

sources (such as an Extron ShareLink device) to these female HDMI digital video 
connectors. Use the Extron LockIt device to secure the HDMI cable at the switcher 
(see 

Securing the HDMI Cable

 on page 9 for securing the cable).

C

 

Input 7

 

— Input 7 is a dedicated audio-only input for an auxiliary, stereo, line-level 

analog audio signal from an output source such as  an iPod or an MP3 player. 
Connect a cable from the source to this 5-pole captive screw connector. It can be 
wired as balanced or unbalanced (see 

Input 7 Connector Wiring

 on page 63 for 

wiring details). 

D

 

Aux audio port

 

— Connect an aux audio device to this 3.5 mm captive screw 3-pole 

connector for dedicated mono audio only input.

E

 

VoiceLift port

 

— This RJ-45 jack is dedicated for use with the optional VLR 102 or 

VLR 302 VoiceLift Receiver for integration of a VoiceLift Microphone system.

NOTE:

  To install the VoiceLift Microphone system, see the 

VoiceLift Installation 

Guide

, supplied with the device.

F

 

Paging sensor port

 

— Connect the optional Priority Page Sensor (PPS 35 or 

PPS 25) to this port, to enable program audio interruptions during paging system 
broadcasts.

NOTE:

  The Extron Priority Page Sensor is an optional accessory, purchased 

separately. See the Extron 

website

 for details about the Priority Page Sensors. 

To install a Priority Page Sensor system, see the installation guide supplied with 
the applicable device.

Outputs

G

 

HDMI video output

 — Connect a suitable display device to this female HDMI digital 

video output connector. Use the Extron LockIt device to secure the HDMI cable at the 
switcher (see 

Securing the HDMI Cable

 on page 9 for securing the cable).

H

 

Line out audio output

 — Connect an external amplifier, recording, podcasting, or 

assisted listening device to this 3.5 mm captive screw 5-pole connector.

I

 

Amplified audio output

 — Connect speakers to this 5 mm captive screw 4-pole 

connector. The amplified audio is capable of outputting 50 watts (2 x 25 watts RMS) 
for 4 and 8 ohm speakers (see 

Speaker Configuration

 on page 56 for wiring 

details).

PVS 407D Switcher • Rear Panel Connections

6

Содержание PVS 407D







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды