Extron electronics PVS 407D, Руководство пользователя

Страница: 15 / 70

Final Setup
With an MLC Plus 100 as a standard MLC controller in the PoleVault system package, the
PVS 407D switcher completed setup should look similar to the figure below.
Ensure all connections are correctly made and secure. Use LockIt brackets to secure
HDMI cables (see below).
NOTE:
See the
PoleVault System Installation Guide
and
MLC Plus 50/100/200
Series Setup Guide
for full MLC installation, configuration, and operating details.
1 3
2 4
DO NOT
GROUND
OR SHORT
SPEAKER
OUTPUTS
4/8
Ω
HDMI HDMI
1/2
SIG LINK SIG LINK
3/4 5
6
INPUTS
OUTPUT AUDIO OUT
PVS 407D
AMPLIFIED AUDIO OUT
PAGING
SENSOR
PVT IN PVT IN
L R
AUX
OVER PVT REMOTE
VOICELIFT
LAN
INPUT 7
+V
L R RS-232
Tx Rx
IR
S G G
CLASS 2 WIRING
LAN
3A MAX
POWER
12V
L R
Audio Output
to Speakers
Red Positive (+)
Black Negative (-)
Speaker
wire color
PVS terminal
(left and right)
Supplied PVS
Switcher External
Power Supply
(12 VDC, 4 A, or
12 VDC, 4.2 A)
4-port 10/100 Ethernet Switch
Connect as follows:
1. TCP/IP network
2. MLC controller
3. Optional network device
4. Optional network device
Power Connector
HD
M
I/R
G
B
PVT HD RGB
HDMI or RGB video/audio,
Inputs 1/2 and 3/4,
1 XTP DTP 24 cable with RJ-45 connectors
VGA IN
AUDIO IN AUDIO IN
HDMI IN
e
MLC Plus 100
RS-232 input
MLC Plus 100 rear panel
Ground (Gnd)
Transmit (Tx)
Receive (Rx) Transmit (Tx)
Receive (Rx)
White Rx on RS-232 port
Violet Tx on RS-232 port
Drain wire Ground (G)
Black
PVS Power Supply (–)
Red PVS Power Supply (+)
MLC
wire color
To PVS terminal
A
Aux Audio
Input 5
C
Aux
Input
D
VoiceLift
Receiver
E
HDMI Output to
Display Device
HDMI
Connector
G
Line Out
Output
(Audio)
Paging
Sensor
Input
+V
F
H I
L
IR control
S G
K M
HDMI Input
Sources,
Inputs 5 and 6
HDMI
Connector
B
Connect to the
same power supply
used by the PVS Switcher.
NOTES:
• If you use cable that has a drain wire, tie the drain wire
to ground at both ends.
• You must connect a
ground wire between the MLC
and PVS.
J
Ground
+12 VDC input
Tx Rx G Tx Rx G 1 2 C G C V G S
POWER
12V
x.xA MAX
COM 1 COM 2 VOL IR
G IN
D IN RELAYS
Figure 7. PVS 407D Connections
Securing the HDMI Cable
The supplied Extron LockIt HDMI cable lacing bracket makes
it possible to secure a standard HDMI cable to the PVS 407D
switcher.
To securely fasten an HDMI cable to the PVS 407D (see image
at right):
1
Plug the HDMI cable into the rear panel HDMI connector.
2
Loosen the HDMI connection mounting screw from the
rear panel enough to allow the LockIt lacing bracket to be
placed over it. The screw does not have to be removed.
3
Place the LockIt lacing bracket on the screw and against
the HDMI cable connector.
4
Lightly tighten the screw to secure the bracket.
5
Place the included tie wrap around the HDMI connector
and the LockIt lacing bracket and tighten as shown in the
images at right.
7
OUTPUT
3
3
LLLL LLLLLLLLL
2
1
3
4
5
PVS 407D Switcher • Rear Panel Connections 9