2
PowerCage 411 Enclosure • Setup Guide (Continued)
1.
Where applicable, remove as many blank plates
or previously installed boards from the rear of the
PowerCage Enclosure as necessary to accommodate the
number of new boards to be installed.
2.
Carefully slide the board into the slot, aligning the bottom
edge of the board with the left and right board mounting
slides on the bottom of the enclosure slot. Push the board
completely into the slot and finger-tighten the two top
screws while pushing in the screws to secure the board in
place (see figure 2).
3.
Repeat
step
2
for all boards needing installation.
NOTE:
Cover all empty board slots; do not leave them
open. Securely fasten the screws for all boards and
blank panels.
FOX3 T 301 PC
RS-232
Rx
G
Tx
AUDIO IN
HD
MI
INP
UT
LO
OP
OU
T
OUT IN
OUT IN
USB HID
USB 2.0
A
B
RS-232
LAN
Rx
G
Tx
REMOTE
FOX3 T 301 PC
RS-232
Rx
G
Tx
AUDIO IN
HD
MI
INP
UT
LO
OP
OU
T
OUT IN
OUT IN
USB HID
USB 2.0
A
B
FOX3 T 301 PC
RS-232
Rx
G
Tx
AUDIO
IN
HD
MI
INP
UT
LO
OP
OU
T
OUT IN
OUT IN
USB HID
USB 2.0
A
B
FOX3 T 301 PC
RS-232
Rx
G
Tx
HD
MI
INP
UT
LO
OP
OU
T
OUT IN
OUT
IN
USB 2.0
A
B
Screws
(2 per board)
Align board and
slide into slot.
Figure 2.
Board Installation
Front Panel Features
ADJUST
MENU
NEXT
RESET
POWERCAGE 411
215W
POWER SUPPLY
215W
POWER SUPPLY
CONFIG
E
A
A
A
D
D
D
C
C
C
C
C
C
A
A
A
C
C
C
C
C
C
G
G
G
H
H
H
F
F
F
B
B
B
B
B
B
B
B
B
B
E
E
E
Figure 3.
PowerCage 411 FOX3 Front Panel
A
Power supply LEDs
—
LED Color - State
Power Supply Status
Fan Status
Green - Solid
Good
Both fans functional
Red - Solid
Failed
Both fans functional
Orange - Solid
No AC power present
Both fans functional
Green - Blinking
Good
Either fan not functional
Red - Blinking
Failed
Either fan not functional
Orange - Blinking
No AC power present
Either fan not functional
B
Power supplies
— Connect power to IEC power connector 1 or 2 (see
C
Fans
— For power supplies.
D
Configuration port
— If desired, connect a host device to the front panel USB mini-B port for configuring the enclosure.
NOTE:
This port allows communication to the enclosure and the boards.
E
LCD screen
— The screen displays messages, menu information, and your selections (see
F
Reset button and LED
— Pressing the
Reset
button sets various enclosure settings to the factory default values. The LED
lights green after pressing the
Reset
button (see the
PowerCage 411 Series User Guide
for details).
G
Navigation buttons
—
•
MENU
— Press
MENU
to access the PowerCage 411 menu system (see
Menus, Configuration, and Adjustments
).
•
NEXT
— From each menu press
NEXT
to step through submenus (see
Menus, Configuration, and Adjustments
).
H
Navigation adjust knobs
—
•
Horizontal
— Turn the horizontal adjust knob to navigate the menu system (see
).
•
Vertical
— Turn the vertical adjust knob to navigate the menu system (see
Menus, Configuration, and Adjustments
2
3