manualshive.com logo in svg

Extron electronics NAV SD 101, Руководство пользователя

Поделиться
Скачать
Extron electronics NAV SD 101 Скачать руководство пользователя страница 17

NAV SD 501 and NAV SD 101 Scaling Decoders • Installation

9

 PRELIMINAR

Y

Analog audio connectors

See figure 5 to wire a connector for the appropriate output type. Connectors are included 
with the decoder, but you must supply the audio cable. Use the supplied tie-wrap to strap 
the cable to the extended tail of the connector.

Unbalanced Stereo Output

Balanced Stereo Output

Do not tin the wires!

Tip

No Ground Here

No Ground Here

Tip

LR

Sleeves

Tip

Ring

Tip

Ring

LR

Sleeves

Figure 5. 

Captive Screw Connector Wiring for Audio Outputs

ATTENTION

:

• 

For unbalanced audio, connect the sleeves to the ground contact. 

DO NOT

 

connect the sleeves to the negative (-) contacts.

• 

Pour l’audio asymétrique, connectez les manchons au contact au sol. 

NE PAS

 

connecter les manchons aux contacts négatifs (–).

NOTES:

• 

The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).

• 

If the stripped section of wire is longer than 3/16 inch, the exposed wires may 
touch, causing a short circuit.

• 

If the stripped section of wire is shorter than 3/16 inch, wires can be easily pulled 
out even if tightly fastened by the captive screws.

• 

Do not tin the power supply leads before installing them in the connector. Tinned 
wires are not as secure in the connector and could be pulled out.

A balanced stereo audio connector consists of a tip, ring, and 

Sleeve (   )

Ring (-)

Tip (+)

3.5 mm Stereo Plug Connector

(balanced)

 

sleeve. An unbalanced mono audio connector consists of a tip 
and sleeve. When you are making connections for the units 
from existing audio cables, see the drawing at right to identify 
the tip, ring, and sleeve parts of the connector. The ring, tip, 
and sleeve wires are also shown on the captive screw audio 
connector diagram, figure 5.

Control connector wiring

Figure 6 shows how to wire the Control (RS-232 and IR) connector.

Tx

Rx

Rx

Tx

Gnd

IR Device

RS-232 Device

RS-232

Tx

Rx

GS

G

IR

CONTROL

Figure 6. 

Control Connector Wiring

NOTES:

• 

The IR S and G line pair and the RS-232 Tx and Rx line pair must each cross once 
between this connector and the source or destination.

• 

The length and preparation of exposed wires is important (see the audio connector 

NOTES

 above for details).

Содержание NAV SD 101



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды