background image

IR 501 Small Matrix Remote Control • Operations

IR 501 Small Matrix Remote Control • Operations

Operations

Introduction

3

2

IR 501 Small Matrix Remote Control • Battery Installation

IR 501 Small Matrix Remote Control • IR 501 Buttons

About this User’s Guide

This user’s guide covers the Extron IR 501 Small Matrix Infrared
(IR) Remote Control, part #

70-336-01

.  The IR 501 is an optional

remote control that works with Extron matrix switchers.  The
remote control can duplicate most of the matrix switcher’s front
panel control functions and some of RS-232 control functions.
The hand-held remote operates at a carrier frequency of 38 kHz.

Refer to the appropriate matrix switcher manual for
definitions of ties, configurations, presets, and audio
breakaway; and for more detailed descriptions of the
switcher’s front panel indications.

Battery Installation

Install two AAA batteries as shown (figure 1).

Figure 1 — Battery installation

IR 501 Buttons

Aim the hand-held unit at the IR detector on the switcher and
press the desired buttons on the remote.  The maximum
operating range is 30 feet.

After the definitions of the IR 501’s buttons, see 

Operations

 for

examples of using the IR 501 to perform various functions.

I/O

 buttons

1

Input/Output Selection buttons

 — The I/O buttons select

inputs and outputs to tie.  The switcher’s front panel Input
LEDs indicate the selected input or output.

These buttons also select among presets to save or recall.

2

+10 button

 — The +10 button

is used with the other I/O
buttons to select numbers
higher than 0 through 9.

3

Enter button

 — The Enter

button saves changes when
you create a new tie or
configuration.

{function}

 buttons

4

Input and Output buttons

 —

The Input and Output buttons
determine whether the I/O
buttons select an input or
output(s) when pushed.

5

Video and Audio buttons

 —

The Video and Audio buttons
select video or audio inputs
and outputs when creating or
viewing a tie or when muting
an output.

The default selection is
both video and audio
selection.  If you want to
configure both video and
audio, you do not need
to push the Video or
Audio button.

6

Preset and Save buttons

 — When you push the Preset

button before you press an I/O button, the I/O button
selects a preset to save or recall when it is pushed.

When you push the Save button before you push the Preset
button, the current configuration is saved as a preset when
you push an I/O button.

7

Mute buttons

 — The Mute button blanks the screen and/

or silences the audio.

The Unmute button unmutes all video and audio outputs.

Figure 2 — IR 501 buttons

SMALL MATRIX REMOTE

INPUT/OUTPUT SELECTION

1

2

3

4

5

6

7

8

PRESET

SAVE

VIDEO

AUDIO

MUTE

UNMUTE

INPUT

OUTPUT

9

0

+10

ENTER

IR 501

6

7

1

3

2

5

4

Содержание IR 501

Страница 1: ...1 Unmute an output Press the UNMUTE button to unmute all video and audio outputs All of the switcher s Output LEDs flash on for a second Troubleshooting If the switcher does not properly respond to IR remote control functions check the following You may be too far from the switcher The maximum operating range is 30 feet You may be too far to the side of the switcher The remote control must be poin...

Страница 2: ...n buttons The I O buttons select inputs and outputs to tie The switcher s front panel Input LEDs indicate the selected input or output These buttons also select among presets to save or recall 2 10 button The 10 button is used with the other I O buttons to select numbers higher than 0 through 9 3 Enter button The Enter button saves changes when you create a new tie or configuration function button...

Страница 3: ...les show operations with specific input output and preset numbers Use your own numbers as desired The switcher s Power LED flashes whenever the switcher receives an IR command Other switcher indications are identified in the following examples where appropriate For detailed descriptions of how the switcher indicates ties and presets refer to the appropriate matrix switcher s manual Many operations...

Страница 4: ...ut as described in the switcher s manual 4 Allow the switcher s 5 second input and output button timeout to deselect the output Presets Save a preset 1 Create all desired ties 2 Press the SAVE button to specify a save preset operation 3 Press the PRESET button to specify preset mode The switcher s Preset LED blinks and for preset numbers that are within the switcher s total number of inputs and ou...

Отзывы: