Extron electronics EBDB Mini, Руководство по установке

Страница: 2 / 2

2
EBDB Mini • Setup Guide (Continued)
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8351.2188
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
+V
G
-S +S +V
G
-S +S +V
G
-S +S
eBUS DISTRIBUTION HUB
PWR OUT = 6W
V C G
VOL
POWER
12V
1.0A MAX
G Tx Rx RTS CTS
COM 1
3 1 2 4 G
DIGITAL I/O
G Tx Rx
COM 2
-S +V +S G
eBUS
C 1 2
RELAYS
S G
IR/S
LAN
IPCP PRO 250
MAC: 00-05-A6- XX-XX-XX
S/N: ####### E######
IPCP Pro
eBUS port on an
EBP or other
eBUS endpoint
device
+
V
+
S
G
– S
G -S +S +V
Tie drain wires to ground.
G -S +S
G -S +S
Tie drain wires to ground.
G
-S
+S
+V
+
Signal
- Signal
+
12 VDC
Ground
G -S +S +V G -S +S +V
Powered
eBUS
device(s)
eBUS Connections
• Connect up to four (4) eBUS devices to the
EBDB Mini eBUS Distribution Hub.
• Wire the connectors the same at both ends.
EBDB Mini Rear Panel
ATTENTION:
Do NOT
connect the power pin
to any device that is
already powered by the
IPCP Pro control
processor or by an
additional power supply.
3/16" (5 mm) Max.
Figure 3.
eBUS Wiring for a System with Two Power Sources
Installation
1.
Mount the EBDB Mini as desired and mount the IPCP Pro to a rack or furniture (see the IPCP Pro User Guide at
www.extron.com ).
2.
Connect the EBDB Mini and any eBUS endpoint devices to each other in a daisy-chain or a star arrangement (see the eBUS
Technology Reference Guide for information about daisy chain and star topologies). Wire both ends of each cable the same
(pin 1 to pin 1, pin 2 to pin 2, and so forth).
3.
Connect the IPCP Pro to the EBDB Mini, making sure that both ends of the cable are wired the same.
NOTE: See the attention information in figure 3 so you do not connect the power pins (labeled V+) on the EBDB Mini to
two powered devices. Power should be supplied to the EBDB Mini by only one source.
4.
Connect power to the devices, connect the IPCP Pro to a network, and set up the IPCP Pro and its connected eBUS
endpoint devices.
Additional Instructions, Information, and Assistance
•
Instructions on configuration are available in the user and setup guides for the IPCP Pro control processor and in the Global
Configurator Help file. The Global Configurator Help file includes an introduction to the software and how to start a GC
project, as well as instructions on configuration.
•
See the eBUS Technology Reference Guide for details about eBUS addresses, topologies, and firmware updates.
•
Software, help files, and guides are all available at www.extron.com .
•
If you have questions during installation and setup, call the Extron S3 Sales & Technical Support Hotline or the Extron S3
Control Systems Support Hotline (1.800.633.9877).
Mounting
You can set an EBDB Mini on a tabletop or attach it to an equipment rack or furniture by using adhesive-backed hook-and-loop
tape.
68-3049-50
Rev. A
10 16
Contact Information