Extron electronics DXP 1616 HD 4K Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 116

Extron electronics DXP 1616 HD 4K Скачать руководство пользователя страница 55

DXP HD 4K Series • Operation

47

I / O

I / O

2 seconds

AUDIO

VIDEO

AUDIO

I/O

ESC

Press and hold
simultaneously.

3 seconds

I/O

VIDEO

AUDIO

The

Esc

,

Video

,

and

Audio

LEDs

blink twice.

Release the buttons.

DXP 168 and 1616

DXP 44, 84, and 88

ESC

VIDEO

ESC

Press and hold
simultaneously.

The

Esc

,

Video

,

and

Audio

LEDs

blink twice.

Release the buttons.

Figure 74.

Toggling between Lock Modes 1 and 2

Switching from Lock Mode 1 to Lock Mode 0

If the switcher is in lock mode 1, you cannot change it directly to lock mode 0 (completely
unlocked). You must first place the switcher in lock mode 2, then

toggle it to mode 0

(see

Selecting Lock Mode 2 or Toggling Between Mode 2 and Mode 0

beginning on

page 45).

Resetting

There are several methods by which you can reset the DXP, and some of these methods
allow for four levels of resetting. The following reset methods are available on the DXP:

•

Front panel buttons

(see

Resetting the System from the Front Panel

)

•

Rear panel Reset button

Resetting Using the Rear Panel Reset Button

on

page 49)

•

SIS commands

(see the

Reset mode commands

in the Command and Response

Table for SIS Commands, page 76)

•

PCS configuration software

(see the program help file)

Resetting the System from the Front Panel

A system reset (also known as a “hard reset” does the following:

•

Clears all ties and presets.

•

Clears all video and audio setup and mutes.

NOTE:

The system reset does not reset the Internet protocol (IP) settings or replace

user-installed firmware.

The front panel reset is identical to the

E

ZXXX

}

SIS command (see the

«
...
53
54
55
56
57
...
»

Содержание DXP 1616 HD 4K





















































































































Отзывы:

Нет отзывов