Extron electronics DVI-RGB 150, Руководство пользователя, Страница: 9 / 14

DVI-RGB 150 • Installation and Operation
Installation and Operation, cont’d
2-6
DVI-RGB 150 • Installation and Operation
2-7
7 . Slide the device in or out until it is in the desired position.
Tighten the screws installed in step
2 .
If the screws are inaccessible to a screwdriver:
a . Mark the location of the brackets relative to the screws.
b . Remove the transmitter or receiver from inside the
furniture.
c
. Tighten the screws.
d . Replace the unit inside the surface (step 6 ).
Rear Panel Connections and Controls
a
Input connector — Connect a single link of direct digital video
to this 25-pin DVI-D connector (fi gure 2-5) using the included
cable.
100-240 50/60 Hz
0.35A MAX
OUTPUT
INPUT
BUFFERED
LOOP-THROUGH
R
H
G
V
B
S
SOG ON/OFF REFRESH
DDC
SOURCE
MONITOR
HIGH
LOW
SELECTOR
OUTPUT
RESOL.
DVI-RGB 150
2 1 5 7 3 6 4
Figure 2-5 — DVI-RGB 150 rear panel
b
Buffered Loop-through connector — If desired, connect a direct
digital local monitor to this 25-pin DVI-D connector.
c
Output connectors — Connect an RGB display to these female
BNC connectors.
For RGBHV video — Connect to fi ve
BNC connectors as shown at right.
Ensure that the SOG On/Off switch
(
f
)
is turned off.
For RGBS video —
Connect to four BNC
connectors as shown at right. Ensure that
the SOG On/Off switch
(
f
) is turned off.
For RGsB video — Connect to three BNC
connectors as shown at right. Ensure that
the SOG On/Off switch
(
f
) is turned on.
R
H
G
V
B
S
R
H
G
V
B
S
R
H
G
V
B
S
DDC
SOURCE
MONITOR
SELECTOR
d
DDC Source switch — Set this switch to the Monitor ( up )
position to connect the DDC channel between the direct
digital video source and the local monitor.
Set this switch to the Selector ( down ) position to connect
the DDC channel between the direct digital video source
and the built-in DVI-RGB 150 DDC logic.
e
Output Resolution rotary switch — If the DDC Source
switch (
d
) is in the Selector position, set this switch to the
appropriate position to select the desired video resolution.
Use the Refresh DIP switch
(
f
) to select the refresh
rate. The table below identifi es the switch positions and the
associated resolutions and vertical refresh rates.
Pos. Resolution
Output Resol.
Switch
Refresh
DIP Switch
0 640x480
1
2 852x480
3 1024x768
6
8
9
A
B
60 Hz 75
60 Hz 75
60 Hz 75
60 Hz 75
4
5
1024x852
1280x768
60 Hz 75
60 Hz 75
7
800x600
1280x1024
1366x768
1400x1050
1600x1200
480p
Pos. Resolution
60 Hz 75
60 Hz 75
60 Hz 60
60 Hz 60
60 Hz 60
< >
Dwn Up
1365x768 60 Hz 75
C
D
E
F
576p
1080i
1080p
720p
50 Hz 50
50 Hz 60
50 Hz 60
50 Hz 60
Refresh
DIP Switch
< >
Dwn Up
Output Resol.
Switch
N
Many monitors will not support all of the resolutions and
refresh rates shown. If you get no display, try a different
rate.
f
SOG (Sync on Green) On/Off switch— Set this switch to
the On ( up ) position to enable SOG for RGsB video. Set
this switch to the Off ( down ) position to disable SOG for
RGBS or RGBHV video.
Refresh switch — If the DDC Source switch (
d
) is in the
Selector position, set this switch either up or down to select
the refresh rate of the selected output. See the table above.
g
AC power connector — Plug a standard IEC power cord
into this connector to connect the interface to a 100 to 240VAC,
50 Hz or 60 Hz power source.
SOG ON/OFF REFRESH
HIGH
LOW
OUTPUT
RESOL.