Extron electronics DTP2 T 203, Руководство по установке

Страница: 2 / 4

2
DTP2 T 203 • Setup Guide (Continued)
5. Connect an RJ-45 DTP or HDBT receiving device to the output (see figure 2 ,
E
on the previous
page) for either DTP or HDBT model (see image to the right to properly wire the RJ-45 connector).
•
For DTP2 series receivers , set the DTP/HDBT switch (
F
) to DTP and the SEND POWER switch
( D ) to the
UP (
SEND POWER
)
position.
On the receiver, set the
SEND POWER
switch to the
DOWN ( OFF ) position (see figure 3 below) .
•
For legacy DTP series
, set the DTP/HDBT toggle switch ( F ) to DTP
,
and the SEND POWER
switch to the DOWN (OFF) position (see figure 3 below).
•
If the receiver is
HDBaseT enabled
, set the DTP/HDBT toggle switch ( F ) to HDBT , and the SEND
POWER switch (
D
) to the DOWN ( OFF ) position.
ATTENTION:
• Position these toggle switches (see figure 2 ,
D
and
F
) BEFORE connecting the appropriate device to the TP
connector. Failure to comply can damage the endpoint.
• Positionnez ces sélecteurs (voir figure 2,
D
et
F
) AVANT de connecter l’appareil approprié au connecteur TP. Ne
pas respecter cette procédure pourrait endommager le point de connexion.
• The DTP2 T 203 device is configured to output power to DTP2 models only. If connected to a legacy DTP or
HDBT device , set the SEND POWER toggle switch to the DOWN position (OFF). Failure to turn the power OFF will
damage the connected DTP device.
• Le DTP2 T 203 est configuré pour fournir une alimentation aux modèles DTP2 uniquement. S’il est connecté
à un autre appareil, veuillez positionner l’interrupteur à bascule sur « DOWN » (OFF). Si l’interrupteur n’est pas
positionné sur OFF, vous risquez d’entraîner la défaillance de l’appareil legacy DTP connecté.
NOTE:
When the output is configured for DTP mode , remote power is available for Extron DTP2 devices only. When the
output is configured for HDBT mode , remote power is disabled and both the switcher and receiver require their own
12 VDC power supply.
Figure 3. Send Power Toggle Switch Configuration
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T
568 B
TP Wires
12345678
Pins:
5
Pin
1
2
3
6
7
8
4
DTP2 R 211
CONFIG
INPUT
LINK
OUTPUT
SEND
POWER
OFF
STATUS
SEND
POWER
OFF
SEND
POWER
OFF
DTP2 R 211
CONFIG
INPUT
LINK
OUTPUT
SEND
POWER
OFF
STATUS
SEND
POWER
OFF
SEND
POWER
OFF
SEND
POWER
OFF
DTP HDMI 330 Rx
OVER DTP
RS-232 IR
Tx Rx Tx Rx G
OFF
OFF
ON
ON OFF
POWER
OFF
POWER
12V
1.5A MAX
INPUTS
AUDIO 1
HDMI
2
HDMI DP
3
LINK
OUT
DTP
HDBT
OFF
SEND
POWER
SIG
OVER TP
REMOTE
LAN
Rx G Tx Rx Tx G
RS-232 IR
Rx Tx
CONTACT IN RS-232
1 2 3 G 1 2 3 +V
TALLY OUT
POWER
OFF
POWER
12V
1.5A MAX
INPUTS
AUDIO
1
HDMI
2
HDMI DP
3
LINK
OUT DTP
HDBT
OFF
SEND
POWER
SIG
OVER TP
REMOTE
LAN
Rx G Tx Rx Tx G
RS-232 IR
Rx Tx
CONTACT IN RS-232
1 2 3 G 1 2 3 +V
TALLY OUT
POWER
OFF
POWER
12V
1.5A MAX
INPUTS
AUDIO 1
HDMI
2
HDMI DP
3
LINK
OUT DTP
HDBT
OFF
SEND
POWER
SIG
OVER TP
REMOTE
LAN
Rx G Tx Rx Tx G
RS-232 IR
Rx Tx
CONTACT IN RS-232
1 2 3 G 1 2 3 +V
TALLY OUT
Local
Power Supply
CATx Cable
up to 330' (100 m)
Local
Power Supply
No Remote Power
Extron
DTP2 T 203
Transmitter
Extron
DTP HDMI 4K 330 Rx
Receiver
DTP2 Endpoint Connected to a DTP Endpoint
CATx Cable
up to 330' (100 m)
Direction of
Remote Power
Local
Power Supply
Extron
DTP2 T 203
Transmitter
Extron
DTP2 R 211
Receiver
CATx Cable
up to 330' (100 m)
Direction of
Remote Power
Extron
DTP2 T 203
Transmitter
Extron
DTP2 R 211
Receiver
DTP2 Endpoint Connected to a DTP2 Endpoint
Local
Power Supply