Extron electronics DMP 64 Plus, Руководство пользователя

Страница: 34 / 99

DMP 64 Plus • Dante Controller 27
Physical Dante Network Setup
A physical network is required to share Dante audio channels between Dante-enabled
devices like the DMP 64 Plus. Other Dante-enabled devices must be on the same physical
network in order to communicate via Dante. A daisy chain topology can be used to connect
multiple devices.
Daisy Chain topology has DMP 64 Plus units connected in succession (see figure 33).
INPUTS
I/O
OUTS
DMP EXP
AT
ACP
REMOTE
USB AUD
LA
N
/Vo
IP
R
1 2 C V AT 1 (PRI) PoE+ 2 (SEC)
RS-232
Tx +V
IN G O IN G O IN G O IN G O IN G O IN G O
+S -S Rx G G
1 2 3 4 5 6 1 2 3 4
POWER
12V
2.0A MAX
1 2 3 4 5 6
INPUTS
I/O
OUTS
DMP EXP
AT
ACP
REMOTE
USB AUD
LA
N
/Vo
IP
R
1 2 C V AT 1 (PRI) PoE+ 2 (SEC)
RS-232
Tx +V
IN G O IN G O IN G O IN G O IN G O IN G O
+S -S Rx G G
1 2 3 4 5 6 1 2 3 4
POWER
12V
2.0A MAX
1 2 3 4 5 6
INPUTS
I/O
OUTS
DMP EXP
AT
ACP
REMOTE
USB AUD
LA
N
/Vo
IP
R
1 2 C V AT 1 (PRI) PoE+ 2 (SEC)
RS-232
Tx +V
IN G O IN G O IN G O IN G O IN G O IN G O
+S -S Rx G G
1 2 3 4 5 6 1 2 3 4
POWER
12V
2.0A MAX
1 2 3 4 5 6
INPUTS
I/O
DMP EXP
AT
ACP
REMOTE
USB AUD
LA
N
/Vo
IP
R
1 2 C V AT 1 (PRI) PoE+ 2 (SEC)
RS-232
Tx +V
IN G O IN G O IN G O IN G O IN G O IN G O
+S -S Rx G G
1 2 3 4 5 6 1 2 3 4
POWER
12V
2.0A MAX
1 2 3 4 5 6
Ethernet
Figure 33. Daisy Chain Network Topology
NOTE:
The daisy chain topology only functions in switched mode. It is not possible to
use in redundant mode.
Redundant Configuration
In redundant mode, the 2-port AT switch (see
figure 2
,
C
on page 4) becomes
separate primary and secondary ports that duplicate audio traffic. Port 1 is marked
(PRI)
PoE+
for primary while port 2 is marked
(SEC)
for secondary (see figure 183 below).
Primary and secondary switches/ports cannot be connected together anywhere in the
audio network. Redundant configuration can be enabled using Dante Controller or DSP
Configurator.
To configure the DMP 64 Plus in redundant mode using Dante Controller:
1. Open Dante Controller.
2. Press <Ctrl+D> on the keyboard to access the
Device View
dialog box.
3.
Select the desired DMP 64 Plus from the (Choose a Dante Device...) drop-down
menu (see figure 34,
1
).
Figure 34. Redundant Mode Configuration in Dante Controller
4. Select the Network Config tab (
2
).
5. From the
Dante Redundancy
panel, use the drop-down to select Redundant (
3
).
NOTE: To configure the DMP 64 Plus in redundant mode using DSP Configurator, refer
to the DSP Configurator Help File .
33
34