CTL208CM Control Panel Module • Installation
CTL208CM Control Panel Module • Installation
Installation, cont’d
9
Program the control panel module’s buttons as desired,
using either the Extron ICS100 control software or the
Extron serial character command set. See
ICS100 Windows
Control Program
and/or
Serial Commands
in chapter 4,
Serial
Communications
, for details.
10
If necessary, configure the control panel module’s serial
control protocol settings (baud rate, data bits, and stop
bits) to match those of the device to be controlled. See
ICS100 Windows Control Program
and/or
Serial Commands
in chapter 4,
Serial Communications
, for details.
11
If necessary, reconfigure the control panel module’s rear
panel DIP switch 1 to match the serial protocol (RS-232,
RS-422, RS-485) of the device to be controlled. See
Rear
Panel Setup
, in this chapter for details.
12
If the computer, control panel module, and the device to
be controlled are not part of an RS-485 serial port daisy
chain, disconnect the serial control cable from the
computer and install the serial control cable between the
control panel module and the device to be controlled.
If the rear of the control panel module will be inaccessible
when the installation is complete, the operation of the
module should be tested before the final mounting.
13
Apply or connect power to all devices in the system.
14
Test the system:
Ensure that the controlled device
responds as desired to the control panel module buttons.
If necessary, correct the programming and/or the system
wiring. Ensure that you remove electrical power if you
need to change the system wiring. Test the system again.
15
Disconnect power
from the control panel module and
other devices.
16
Mount the control panel module into any Extron four-
space mini-AAP connector panel.
If the rear of the control panel module will be inaccessible
when the installation is complete, all cables, including
the power connector on the CTL208, must be connected
before the permanent installation.
17
Mount the mini-AAP connector panel to the mini-AAP
mounting option as necessary. See
Wall mounting
in this
chapter for details about wall mounting the panel.
18
Restore power to all devices.
2-3
Installation Overview
CAUTION
Installation and service must be performed by
authorized personnel only. UL Listed electrical
boxes are recommended. See
UL Requirements
for Wall Box Installation
in this chapter.
1
If desired, order a custom engraved front panel. Contact
the Extron S
3
Sales & Technical Support Hotline to order
the panel.
2
Power off all devices and disconnect them from the
power source, if necessary.
3
Run a serial cable between the site where the CTL208CM
control panel module will be installed and the site of the
serial-controlled device.
4
For installation in a wall or furniture
, prepare the site:
cut a hole in the surface, install the electrical box or
mounting bracket, and prepare the cables. See
Wall
Mounting Site Preparation
in this chapter. See appendix A,
Reference Information
, for a partial list of devices that can
accept four space mini-AAPs.
5
For other installations
, install a tabletop or in-table
connector bay, or other mini-AAP mounting option.
Refer to the manual for the device in which the control
panel module will be installed. See appendix A,
Reference
Information
, for a partial list of devices that can accept four
space mini-AAPs.
6
Connect a serial cable between the control panel module
and a computer. See
Rear Panel Setup
, in this chapter for
details.
Alternatively, you can connect the control panel module
to an RS-485 serial port daisy chain that includes the
programming computer and the device to be controlled.
In a daisy-chain configuration, you can make changes to
the control panel module’s button programming as
needed, without removing the panel from its installation.
7
If necessary, configure the control panel module’s rear
panel DIP switches to match the serial protocol (RS-232,
RS-422, RS-485) of the computer used to program the
control panel module. See
Rear Panel Setup
, in this chapter
for details.
8
Connect the power source to the control panel module.
See
Rear Panel Setup
, to wire the power connector.
Installation
2-2
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203