Extremis AMAi chef, Руководство по сборке

Страница: 53 / 64

53
where you want to assemble the AMAi. Make sure
that the blocks are about 160 cm apart.
2. Place the footrest on the 2 expanded polystyrene
blocks.
3. Fit the first A-frame onto one end of the footrest,
with the Extremis logo facing the outer side using
2 M10x45 carriage bolts, 2 M10 cap nuts and
spring washers.
4. Now attach the two A-frames to the other end of
the footrest by inserting M10x50 carriage bolts
through the holes in the footrest and the A-frame.
5. Now place two expanded polystyrene blocks on
the ground again and put the two footrests on top.
6. Slide the footrest over the two protruding
carriage bolts on the A-frame and secure with
two nuts and spring washers.
7. Now attach the third A-frame to the other end of
the second footrest, with the Extremis logo facing
the outer side.
8. Now attach a set screw M10x35 in the outer
A-frames and one set screw M10x40 in the middle
A-frame(s) as shown in the drawing. Make sure the
set screw is centered to the A-frame.
9. In case of lighting & electricity or shade, first
follow the steps in manual LAB161 or LAB168-1
10. Position the top tube between the two A-frames.
a. Slide the top tube over the adjusting screws so
that it is correctly located.
b. First screw an M10 cap nut and spring washer
onto two adjusting screws to hold the top tube in
place.
11. Then repeat the procedure for the second top tube.
12. Now attach the top tube on the two A-frames,
each using two M10x25 carriage bolts and M10
cap nuts and washers. Now tighten all the screws,
Max. 15Nm.
13. Screw an M10 cap nut and spring washer onto
the outside of each of the two adjusting screws,
as well as a rubber cap with Extremis logo in the
large holes as shown in the drawing. Remove the
expanded polystyrene blocks.
14. a. Insert the pins through the four holes on each
A-frame.
b. Make sure they are properly centered.
15. Fit a black plastic cap onto each end of the pins
and secure it with an M8x20 screw. Make sure
that the plastic caps fit correctly on the A-frame
and tighten all the screws.
16. You can now position the chef module between
the two A-frames on the lowest caps.
Bar - p38
1. Slide the bar on the highest black caps and rotate
it towards the tabletop as shown in the drawing.
2. Once the bar is in position you can lower it and
let it rest on the lowest black caps.
Glassholder - p40
1. Fix one bolt M5x12 & one hammer nut per side
of the stainless steel glassholder as shown in the
drawing but do not tighten yet. Also the position
of the corners are very important!
2. a. Insert the glassholder in the slots of the top profile.
b. Now tighten the bolts.
Add-on table - p42
1. Hang the add-on table on the two black plastic
caps on the A-frame where you want to use it. You
can choose the desired height by using either the
upper or lower pair of caps.
Screenholder - p44
1. Fit the wire hanger to the desired A-frame by
inserting it into the holes in each side of the A-frame.
2. Fix the plate to the screen using the screws and
spacers provided.
3. You can now hang the plate behind the screen
over the hanger.
Leveling feet - p46
1. Remove the standard plastic caps from the
A-frames.
a. Drill a hole in the plastic cap.
b.
Then pull out the plastic cap using a
screwdriver as shown in the drawing.
2. Fit the new flat-ended caps with internal thread
into the A-frames.
3. Screw the adjustable feet into these caps.
4.
a.
Screw out the adjustable feet until they touch
the ground at each point.
b. Then fix them by tightening the nut.
Floor fastening - p48
1. Remove the standard plastic caps from the
A-frames.
a.
Drill a hole in the plastic cap.
b. Then pull out the plastic cap using a
screwdriver as shown in the drawing.
2. a. Now fit the stainless steel ground anchoring
feet into the A-frames.
b.
Make sure that the disc at the bottom is kept
parallel to the floor and that the hole lines up with
the hole in the A-frame.
3. Insert the small stainless steel part in the feet.
4. Fix the feet using an M8x20 bolt.
5. Now you can also choose the desired height by
sliding the feet up/down and tighten the bolt.
6. Mark the locations on the floor where the anchors
are to be fitted and drill at the points indicated.
7. Use the fasteners that are most suitable for the
surface on which the AMAi is to stand.