Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 383

Страница: 383 / 413

Table 276: Power Specifications

Voltage input range

100-127/200-240 47 to 63Hz

Nominal input ratings

12.5 A max at 115VAC and 6A max at 230VAC at Full 770 W load

Maximum inrush current

45A at Max 264 VAC at 25C with cold start

Output

54 V, 13.2 A max, 770 W

Power supply input socket and cord

IEC/EN 60320-1/C16 AC input receptacles

Power cord wall plug

Refer to

Power Cord Requirements for AC-Powered Switches and AC

Power Supplies

on page 393.

Efficiency

Minimum efficiency: 88% at maximum power output.

Table 277: Environmental Specifications

Operating temperature

-10°C to 50°C (normal operation)

Storage temperature

-40°C to 70°C

Operating humidity

93% relative humidity, non-condensing at 30C

Operational shock

30 m/s

(3 G)

EPS-C2 Redundant Power Supply Technical Specifications

The following tables list the specifications for the EPS-C2 redundant power supply unit (model 10936).

Table 278: Physical Specifications

Dimensions

4.4 cm H x 44.1 cm W x 38.4 cm D
1.73 in H x 17.4 in W x 15.1 in D

Weight (unit only)

1.03 kg (2.27 lb)

Table 279: Other Specifications

Allowable PSU

Summit 750W PoE AC PSU

Power cord input plug/socket

IEC 320 C13/C14

Power cord gauge

Min 18AWG

RPS-90 Redundant Power Supply Technical Specifications

The following tables list the specifications for the RPS-90 redundant power supply unit (model
RPS-90).

Technical Specifications

ExtremeSwitching and Summit Switches: Hardware Installation Guide

383

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching X440-G2 Series, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды