Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 378

Страница: 378 / 413

Table 259: Power Specifications (continued)

Maximum Input Amperages

9 A @ 40 V
7.5 A @ 48 V
5 A @ 72 V

Inrush Current

82 A at 72 V peak

Minimum wire size

14 AWG (1.5 mm

) copper stranded

DC Output

12 V , 25 A/3.3 V , 3.0 A

DC Output Power (W)

300 W

Table 260: Environmental Specifications

Operating temperature

0°C to 50°C (normal operation)

Storage temperature

-40°C to 70°C

Operating humidity

20% to 90% relative humidity, non-condensing

Operational shock

30 m/s

(3 G)

Summit 550 W Power Supplies Technical Specifications

The following power supplies are available for use in X670-G2 and X770 series switches:

•

550 W AC PSU-FB (Model 10925)—AC power supply with front-to-back ventilation airflow

•

550 W AC PSU-BF (Model 10927)—AC power supply with back-to-front ventilation airflow

•

550 W DC PSU-FB (Model 10926)—DC power supply with front-to-back ventilation airflow

•

550 W DC PSU-BF (Model 10928)—DC power supply with back-to-front ventilation airflow

Table 261: Physical Specifications

Dimensions

Height: 1.57 inches (4.0 cm)
Width: 3.07 inches (7.8 cm)
Depth: 13.31 inches (33.8 cm)

Weight

3.64 lb (1.65 kg)

Table 262: AC Power Specifications (Models 10925 and 10927)

Voltage input range

90 to 264 V

Nominal input ratings

100 to 240 V , 50 to 60 Hz, 8 A

Nominal input current at full loads

8 A @ 90 V (low-line), 4 A @ 230 V (high-line)

Line frequency range

47 to 63 Hz

Maximum inrush current

15 A at 25°C (77°F)

Output

12 V , 45 A max, 540 Watts, 3 V , 3 A max, 10 Watts
Maximum continuous DC output shall not exceed 550 Watts.

Power supply input socket

IEC 320 C14

Technical Specifications

ExtremeSwitching and Summit Switches: Hardware Installation Guide

378

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching X440-G2 Series, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды