Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 207 | Manualshive

Страница: 207 / 413

background image

To prepare the cable wires for the 1100 W DC power supply unit, follow these steps:

1 Strip 0.4 inch (10 mm) of insulation from one end of each cable wire.
2 Insert the end of the stripped ground wire (green or green and yellow) all the way into the barrel of

the ring terminal and crimp the terminal securely to the wire.

Figure 156: Attaching a Ring Terminal to a Ground Cable

No ring terminal is required to connect the cable wires (non-ground wires) to the 1100 W DC power
supply.

Installing an 1100 W DC Power Supply

Before installing a Summit 1100 W DC power supply:

•

Verify that the switch rack or chassis has been grounded.

•

Verify that the airflow direction for the power supply is the same as the airflow direction of the
installed fan modules in the switch.

To install the power supply, follow these steps:

1 Attach an ESD-preventive wrist strap to your bare wrist and connect the metal end to an

appropriate ground point on the rack.

2 If necessary, remove a blank panel from the rear of the switch.
3 Verify that the power supply is right side up.

The power supply should be oriented as shown in

4 Verify that the direction of ventilation airflow is the same for both the power supply and the switch.

In a switch with front-to-back airflow, the fan modules are labeled Air Out.

In a switch with back-to-front airflow, the fan modules are labeled Air In.

Installing Your Extreme Networks Switch

ExtremeSwitching and Summit Switches: Hardware Installation Guide

207

«
...
205
206
207
208
209
...
»

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренд: N-Tron Страницы: 20

Бренд: DITEC Страницы: 8

Бренд: IOGear Страницы: 10

Бренд: LevelOne Страницы: 17

Бренд: V7 Страницы: 35

LNK-IMC208P-SFP

Бренд: E-LINK Страницы: 6

Digital Energy STS-400-25-3

Бренд: GE Страницы: 49

Бренд: Quartz Страницы: 43

Бренд: TESmart Страницы: 12

Бренд: X-keys Страницы: 4

Бренд: senva Страницы: 2

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

Бренд: AV Link Страницы: 2

Бренд: Comm-Tec Страницы: 40

Бренд: Grizzly Страницы: 2

Бренд: CityGrow Systems Страницы: 21

Бренд: Gefen Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды