Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 413

background image

5

Building Stacks

Introduction to Stacking
Planning to Create Your Stack
Setting up the Physical Stack

A stack consists of a group of up to eight switches that are connected to form a ring. The stack offers
the combined port capacity of the individual switches. But it operates as if it were a single switch,
making network administration easier.

Stacking is facilitated by the SummitStack feature – part of the ExtremeXOS Edge license.

This chapter describes the supported configurations for stacking switches, the considerations for
planning a stack, and the steps for setting up the hardware. We recommend that you read this chapter
before installing the switches that will make up the stack.

Refer to the Stacking chapter in the

ExtremeXOS 22.6 User Guide

for information about configuring a

stack, maintaining the stack configuration, and troubleshooting.

Introduction to Stacking

Using the SummitStack feature – part of the ExtremeXOS Edge license – a stack can combine switches
from different series, provided that every switch in the stack:

•

Runs in the same partition (primary or secondary).

•

Runs the same version of ExtremeXOS.

•

Includes support for stacking.

The stack operates as if it were a single switch with a single IP address and a single point of
authentication. One switch – called the master switch – is responsible for running network protocols and
managing the stack. The master runs ExtremeXOS software and maintains all the software tables for all
the switches in the stack.

All switches in the stack, including the master switch, are called nodes.

shows four nodes in a

stack, connected to each other by SummitStack cables.

ExtremeSwitching and Summit Switches: Hardware Installation Guide

136

«
...
134
135
136
137
138
...
»

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренд: Accedian Страницы: 2

Бренд: Daxten Страницы: 2

Бренд: hager Страницы: 2

Бренд: hager Страницы: 4

Бренд: hager Страницы: 2

Бренд: PureLink Страницы: 10

Бренд: Aethra Страницы: 1

Бренд: XtendLan Страницы: 24

2X2 VGA SWITCHER

Бренд: Gefen Страницы: 12

TigerAccess SMC7824M/FSW

Бренд: SMC Networks Страницы: 2

Antenna-Disconnect-Switch

Бренд: ADS Страницы: 12

SmartStack STS16-20R

Бренд: Cabletron Systems Страницы: 258

Бренд: ALFAtron Страницы: 15

Бренд: SICK Страницы: 299

Бренд: LEGRAND Страницы: 4

velatia cgm.3 system

Бренд: Ormazabal Страницы: 76

Бренд: Stahl Страницы: 29

Ethernet Networks and Web Management

Бренд: GarrettCom Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды