Extreme Networks ExtremeSwitching X435 Series Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 496

background image

Both power supplies are compatible with X460-G2 PoE switch models that have the same airflow
direction as the power supply.

The Summit 715 W AC PSU-FB power supply (Model 10951) is compatible with the X450-G2 PoE and
X465 PoE (-48P, X465-48W, X465-24MU, X465-24MU-24W, X465-24W, X465i-48W) switch models.

The Summit 715 W AC power supplies have a keyed power inlet (C16) that requires a notched (C15)
power cord.

The Summit 715 W AC power supplies have the status LEDs listed in

Table 51: Summit 715 W AC Power Supply LED Status Indications

IN_OK

(Green)

OUT_OK

(Green or Red)

Description

Off

Off

No AC input power connection or low AC voltage.

On

Off

AC input good, 54V output disabled.

On

(Red) On

AC input good, output (54V) fault.

On

(Green) On

AC input good, DC outputs in spec.

Summit 750 W AC Power Supply

The Summit 750 W AC power supply is used in the EPS-C2 external power system (see

Redundant Power System

on page 122). Each installed Summit 750 W AC power supply can provide up

to 380 watts of PoE power budget.

The Summit 750 W AC power supply has the status LEDs listed in the following table.

Table 52: Summit 750 W AC Power Supply LED Status Indications

Label and Color State

Meaning

AC OK

Green

Off

No AC input

On

AC input is good.

DC OK

Green

Off

Both DC outputs (55 V and 12 V) are bad or not enabled.

Blinking

One output is enabled and good; the second output is bad or not

enabled.

On

Both the 55 V and 12 V outputs are enabled and good.

ALM

Red

Off

No fault condition exists.

Blinking

Power supply alert: power supply is likely to fail because of a developing

fault, such as abnormal thermal conditions or poor fan performance.

or

One output (55 V or 12 V) is bad.

On

Both outputs (55 V and 12 V) are bad.

Power supply is receiving 3.3 VSB from the system. (AC OK and DC OK

are off.)

Thermal shutdown, fan failure, or any fault condition when both 55 V and

12 V are turned OFF.

Summit 750 W AC Power Supply

Power Supplies for Use with Your Switch

134

ExtremeSwitching Hardware Installation Guide

«
...
132
133
134
135
136
...
»

Содержание ExtremeSwitching X435 Series

















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X435 Series

Бренд: OEZ Страницы: 5

Бренд: I-Tech Страницы: 27

PU-8H8HBTPL-4K22

Бренд: CYP Страницы: 24

S3100-SI Series

Бренд: H3C Страницы: 58

Бренд: Eaton Страницы: 43

Бренд: Velleman Страницы: 5

Бренд: Eaton Страницы: 120

Бренд: Woxcon Страницы: 42

Бренд: MicroNet Страницы: 123

SOLO Airliner RS

Бренд: Virtualfly Страницы: 32

Бренд: Marmitek Страницы: 32

Бренд: Copal Страницы: 9

EG008W - Instant Gigabit Workgroup Switch

Бренд: Linksys Страницы: 27

Бренд: Comm-Tec Страницы: 40

Бренд: Grizzly Страницы: 2

Бренд: Kramer Страницы: 8

GIGAswitch GSR-16

Бренд: Cabletron Systems Страницы: 346

Бренд: Linksys Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды