Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 135

background image

Changing the RBridge ID and VCS ID

If you are planning to connect more than one device in a fabric, each device must have a unique RBridge ID. The default RBridge ID for
the device is 1.

If you are planning more than one VCS fabric, each fabric must have a unique VCS ID. The default VCS ID is 1.

If you need to change an Rbridge ID or VCS ID, you can use either of the following commands:

•

vcs set-rbridge-id

: This changes the existing RBridge ID of a node. An option is available for this command to also change the

VCS ID.

•

vcs vcsid

: This changes the existing VCS ID of a node. An option is available for this command to also change the RBridge ID.

NOTE

Each time that you change the Extreme Networks VCS Fabric configuration, the device resets to the default configuration and
reboot automatically. Make sure to save the configuration before using either of these commands.

For details on using these commands, refer to the

Extreme Network OS Command Reference

and

Extreme Network OS Management

Configuration Guide

.

Network device connections

Refer to the product Technical Specifications for a listing of supported cables.

CAUTION
Before plugging a cable into any port, be sure to discharge the voltage stored on the cable by touching the electrical
contacts to ground surface.

Ethernet or Fast Ethernet hubs

For copper connections to Ethernet hubs, a 1000Base-T device, or another Extreme Networks device, a crossover cable is required. If
the hub is equipped with an uplink port, it requires a straight-through cable instead of a crossover cable.

NOTE

The 802.3ab standard (automatic MDI or MDIX detection) calls for automatic negotiation of the connection between two
1000Base-T ports. Therefore, a crossover cable may not be required; a straight-through cable may work as well.

Workstations, servers, or routers

Straight-through UTP cabling is required for direct UTP attachment to workstations, servers, or routers using network interface cards
(NICs).

Fiber cabling is required for direct attachment to Gigabit NICs or switches and routers through fiber ports.

Network device

For direct attachment from the Extreme Networks device to a Gigabit NIC, switch, or router, you can use either a fiber cabling with an LC
connector or a copper cable with an RJ-45 connector.

Network device connections

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

95

«
...
93
94
95
96
97
...
»

Содержание ExtremeSwitching VDX 6740








































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching VDX 6740

dominion kx III

Бренд: Raritan Страницы: 6

Бренд: Raritan Страницы: 5

DOMINION KSX II

Бренд: Raritan Страницы: 7

Бренд: Raritan Страницы: 2

Бренд: LAUMAS Страницы: 40

Бренд: Perel Страницы: 4

Бренд: Meridian Страницы: 16

Бренд: Server Technology Страницы: 12

SwitchView SC8 DVI

Бренд: Avocent Страницы: 2

DH-PFS3005-5ET-L

Бренд: Dahua Страницы: 13

Бренд: H3C Страницы: 110

Бренд: Extron electronics Страницы: 137

Guard Master 440N-Z2NRS1A

Бренд: Allen-Bradley Страницы: 4

Бренд: Lindy Страницы: 4

EdgeSwitch 8 150W

Бренд: Ubiquiti Страницы: 28

Бренд: Allen-Bradley Страницы: 4

Бренд: Byte Delight Страницы: 12

Бренд: Blackberry Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды