Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 135

background image

2. Enter

configure terminal

to change to global configuration mode

device# configure terminal

Entering configuration mode terminal

3. Enter the

ntp server

IPv4 address

command, where

IPv4 address

is the IP address of the first NTP server in IPv4 format,

which the device must be able to access. The

IPv4 address

variable is optional. By default, this value is LOCL, which uses the

local clock of the principal switch as the clock server.

device(config)# ntp server "132.163.135.131"

To display the NTP server IP address, use the

show ntp status

rbridge-id

rbridge-id

|

all

command. If you are in global

configuration mode, you must enter

do

before the

show

command.

device(config)# show ntp status rbridge-id 1

The request is for the local RBridge unless an RBridge ID is specified.

If you need to remove an NTP server, use the

no

form of the

ntp server

command.

device(config)# no ntp server "132.163.135.131"

Setting the clock (date and time) manually

You should set the clock only if there are no NTP servers configured. Time synchronization from NTP servers overrides the local clock.
Date values are limited to between January 1, 1970 and January 19, 2038.

1. Log in to the device using the admin account.
2. Enter the

clock set

CCYY-MM-DDTHH:MM:SS

command while in privileged EXEC mode.

The following example sets the clock to March 17, 2010, 15 minutes past noon:

device# clock set 2010-03-17T12:15:00

3. To show the clock and time zone settings, use the

show clock

rbridge-id

rbridge-id

|

all

command.

device# show clock

rbridge-id 1: 2012-03-17 12:15:00 America/Los_Angeles

Setting the time zone

You must perform this procedure on

all

devices for which the time zone must be set. However, you only need to set the time zone once

on each device, because the value is written to nonvolatile memory. While not necessary for device operation, setting a time zone is part
of ensuring accurate logging and audit tracking. Time zone changes take effect after a reboot.

Use the

clock timezone

command to set the time zone.

1. Log into the device using an account that has the admin role.
2. Enter the

clock timezone

region/city

command.

The following example changes the time zone to US/Pacific Standard Time:

device# clock timezone America/Los_Angeles

3. Reboot the device.

Setting the date and time

ExtremeSwitching VDX 6740 Hardware Installation Guide

94

9036108-00

«
...
92
93
94
95
96
...
»

Содержание ExtremeSwitching VDX 6740








































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching VDX 6740

Бренд: D-Link Страницы: 73

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 2

TNS5800-8GP16GT-P24VDC

Бренд: 3onedata Страницы: 3

Бренд: Communica Страницы: 5

Бренд: König Страницы: 8

Бренд: Hamlet Страницы: 4

Бренд: Uniclass Страницы: 32

Бренд: T1V Страницы: 2

PICO-GUARD SFI-D1EDPXT6

Бренд: Banner Страницы: 2

Бренд: S+S Страницы: 16

8 PORT SMART SWITCH CE 232D4SS8

Бренд: B&B Electronics Страницы: 29

Smart view IC-1304-IO

Бренд: C&C TECHNIC Страницы: 2

Бренд: H3C Страницы: 77

Бренд: Voith Страницы: 98

Palert PX-01 Series

Бренд: JenLogix Страницы: 48

Plug in Digital Time Switch

Бренд: Grasslin Страницы: 88

Бренд: Exsys Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды