Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 49

Страница: 49 / 135

FIGURE 29

Attaching the medium or long rear brackets to the extensions

Rear bracket, medium or long

Screws, 6-32 x 1/4-in., panhead Phillips

Attaching the rear brackets to the front rack posts

Complete the following steps to attach the rear brackets to the front rack posts.

1. Attach the right rear bracket to the right front rack post using two 10-32 x 5/8-in. screws and two retainer nuts, as shown in

Figure 30

. Use the upper and lower holes in the bracket.

2. Attach the left rear bracket to the left front rack post using two 10-32 x 5/8-in. screws and two retainer nuts. Use the upper and

lower holes in the bracket.

Flush-rear (recessed) mounting the device in the rack

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

Содержание ExtremeSwitching VDX 6740








































































































































Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching VDX 6740, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды