background image

1

Customer Service: [email protected] | www.extrememax.com

5500.5094 - Plow W/ UniMount

5500.5109 - Plow F/ Polaris Sportsman 570

5500.5112 - Plow F/ Cam-Am Outlander

60” UniPlow HD 

Assembly & Operating Instructions

3518ex0121

Includes:

1. 60” UniPlow HD Blade x 1
2. Reversible Wear Bar x 1
3. Pivot Plate x 1
4. Push Tube x 1
5. Tube Plate x 1
6. Pivot Handle Plate (RH) x 1
7. Pivot Handle Plate (LH) x 1
8. Pivot Handle x 1
9. Safety Pin x 2
10. 5/8”-11 x 1.75” Hex Bolt x 1

11. 5/8” Star Washer x 1
12. 5/16”-18 x 1” Carriage Bolt x 1
13. 5/16”-18 Flanged Lock Nut x 5
14. 5/8”-11 x 1.5” Carriage Bolt x 2
15. Pitch Bushing x 2
16. 5/8” Fender Washer x 4
17. 5/8”-11 Lock Nut x 3
18.  7/16”-14 x 0.75” Socket-Head Cap 

Screw x 2

19. 7/16”-14 Lock Nut x 2

20. 5/16”-18 x 1.5” Carriage Bolt x 1
21. 5/16” x 1.25” Fender Washer x 2
22. Pivot Lever Spring x 1
23. Plow Spring x 2
24. Eyebolt x 2
25. 5/16” Flat Washer x 4
26. 5/16”-18 Hex Nut x 4
27. Skid Pad x 2
28. 5/16”-18 x 1.25” Carriage Bolt x 9
29. 5/16”-18 Lock Nut x 9

Read, Follow, and Save These Instructions.

 Warnings: 

•  UniPlow contains heavy components. Exercise extreme caution during assembly and mounting to avoid injury. 

•  Wear appropriate personal protective equipment at all times, including ANSI approved eyewear.

•  Ensure the blade is locked into position and not pivoting freely before plowing. 

•   Plow is not for use by children. Do not use plow near children or allow children to play on the plow.

•  Plow is not for use by inexperienced ATV operators.

•   Never stand or ride on the plow. Always mark intended plow areas prior to snowfall to prevent accidental property damage 

or injury caused by collision with unmarked hazards.

•  Take care when installing plow springs. They will be under tension.

•  Use care when lifting components into place.

•  Make sure that all nuts and bolts are tightened per installation instructions.

•  Never operate this product with missing or damaged parts.

•   Do not exceed 5 mph while plowing snow or operating ATV with plow attached, even with the blade fully raised.

•   Drive slowly over bumpy and rough terrain, driving fast could cause damage to winch or plow.

•   Never raise the plow above point of contact as it could cause damage to machine, plow or winch.

•  Always perform regular inspections and maintenance on plow tubes and hardware before use.

•  Operate with extreme caution on slopes, steep grades, and rough terrain.

•  Be aware of any possible hidden objects under the snow.

•  Do not ram plow blade into snow piles.

•  Know and follow all local snow removal and noise rules and restrictions. Never pile snow outside your property or on 

streets or sidewalks.  Keep areas around fire hydrants, mailboxes, water drains, and electrical boxes clear of snow and never 

pile snow in a way that obstructs their access.

Attach the mount to begin installation. See the mount manual for 

instructions. Do not assemble plow blade or push tubes until the mount is 

installed.

Plow Safety

Read this manual thoroughly before operating your plow. Failure to follow instructions could result in death, serious injury 
or property damage.  If you have questions regarding safe installation and/or use of your plow, contact customer service at 
(651) 358-1862 on regular business days Monday-Friday from 8am-5pm CST, or e-mail [email protected]

Содержание 5500.5094





















Отзывы: