Extreme Flight TURBO RAVEN EXP Скачать руководство пользователя | Manualshive

Страница: 12 / 22

background image

12

10. Locate the rudder and rudder control horns and base plates. Trial fit the horns into position in their
pre-cut slots and confirm alignment. Trace around the baseplate, and remove the covering under the
baseplate. Glue the horns into position using 30 minute epoxy. Wipe away any excess epoxy with a paper
towel soaked in denatured alcohol, re-confirm alignment and set aside to dry. Once dry glue the rudder
into place on the vertical stabilizer using the same method to glue the hinges in place as previously
described.

«
...
10
11
12
13
14
...
»

Содержание TURBO RAVEN EXP























Отзывы:

Нет отзывов

Похожие инструкции для TURBO RAVEN EXP

Бренд: Dancing Wings Hobby Страницы: 2

Бренд: Jamara Страницы: 16

Бренд: 4-Max Models Страницы: 8

Бренд: 4-Max Страницы: 38

Бренд: Bachmann Страницы: 2

Бренд: TBM Страницы: 14

Бренд: BigPlanes Страницы: 9

WILD WEST EXODUS VENGEANCE OF THE EARPS

Бренд: WARCRADLE STUDIOS Страницы: 5

AIRBUS A220-300 / KOREAN AIR

Бренд: Airigami Страницы: 2

Бренд: Goldwing RC Страницы: 49

Junior Fly Ball

Бренд: Amewi Страницы: 8

Mini HIGHroller

Бренд: Team Losi Страницы: 20

6-8-6 Steam Turbine Engine

Бренд: Rail King Страницы: 32

Бренд: LAheli Страницы: 10

Бренд: Creative Paradise Страницы: 2

Бренд: The Drone Warehouse Страницы: 9

E-FLITE UMX ASK-21

Бренд: BNF Страницы: 21

Бренд: Black Horce Model Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды