Extreme Flight 60" Slick 580 ARF Скачать руководство пользователя

Страница: 3 / 33

Items needed for completion:



Masking tape.



Hobby knife with #11 blades.



Thin and medium CA. We highly recommend Mercury M5T thin and M100XF
medium formulas as well as the Mercury glue tips.



30 minute epoxy.



Blue Loctite.



Electric drill with an assortment of small drill bits.



Small flat head and Phillips head screw drivers.



Standard and needle nose pliers.



Side cutter.



Metric ball driver or allen key set.



Sanding block and sandpaper.



4 x METAL GEARED servos with a minimum of 76oz of torque. All flight testing
was performed with Hitec HS-7245MH.



Dubro Long Super Strength servo arm set. (Dubro part #670 for Futaba, #671 for
JR and #672 for Hitec).



2 x 6” Servos Extensions for the Ailerons.



1 x 24” Servo Extension for the elevator servo



Torque 4016T/500 MKII Brushless Outrunner.



Airboss Elite 80 Amp ESC.



6S 3300-4000 mah LiPo battery.



16 x 7 prop.



Optional – Pacer canopy glue and shoe goo adhesive.

Содержание 60" Slick 580 ARF

































Результаты поиска

Содержание 60" Slick 580 ARF

Отзывы:

Похожие инструкции для 60" Slick 580 ARF

Бренды по названию

Популярные бренды

Extreme Flight 60" Slick 580 ARF, Инструкция по эксплуатации

Результаты поиска

Содержание 60" Slick 580 ARF

Отзывы:

Похожие инструкции для 60" Slick 580 ARF

Бренды по названию

Популярные бренды