Extreme Flight 60" laser ARF Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 28

Extreme Flight 60

4

Items needed for completion:



Masking tape.



Hobby knife with #11 blades.



Thin and medium CA. We highly recommend Mercury M5T thin and M100XF
medium formulas as well as the Mercury glue tips.



30 minute epoxy. Mercury Adhesives Epoxies have worked very well for us.



Blue Loctite.



Electric drill with an assortment of small drill bits.



Small flat head and Phillips head screw drivers.



Standard and needle nose pliers.



Side cutter.



Metric ball driver or allen key set.



Sanding block and sandpaper.



4 x METAL GEARED servos with a minimum of 76oz of torque. All flight testing
was performed with Hitec HS-7245MH.



Dubro Long Super Strength servo arm set. (Dubro part #670 for Futaba, #671 for
JR and #672 for Hitec).



2 x 6” Servos Extensions for the Ailerons.



2 x 24” Servo Extensions for the rudder and elevator servos



Torque 4016T/500 MKII Brushless Outrunner.



Airboss Elite 80 Amp ESC.



6S 3300-4000 mah LiPo battery.



16 x 7 prop.

The Ultracote colors used on the Laser are as follows:

Red color scheme: True Red #HANU866, White #HANU870, Midnight Blue
#HANU885 and Gold #HANU879

Yellow/White/Blue color scheme: Bright Yellow #HANU872, White #HANU870,
Midnight Blue #HANU885, Silver #HANU881

«
...
2
3
4
5
6
...
»

Содержание 60" laser ARF





























Отзывы:

Нет отзывов