manualshive.com logo in svg

Extreme Flight RC YAK-54 EXP, Руководство пользователя

Поделиться
Скачать
Extreme Flight RC YAK-54 EXP Скачать руководство пользователя страница 4

4

 

 

Items needed for completion 

-Masking tape 
 
-Hobby knife with #11 blades 
 
-Razor saw 
 
-Thin and medium CA.  We highly recommend Mercury M5T thin and M100XF medium 
formulas as well as the Mercury glue tips.  
 
-30 minute epoxy.  The new Mercury adhesives Epoxies have worked very well for us. 
 
-Blue Loctite. 
 
-Silicon based glue (Zap-A-Dap-A-Goo, etc.) 
 
-Electric drill with an assortment of small drill bits. 
 
-Small flat head and Phillips head screw drivers. 
 
-Standard and needle nose pliers. 
 
-Metric balldriver or allen key set. 
 
-4 sub micro metal geared servos. All flight testing was performed with Hitec HS-65MG 
and HS-5065MG digital servos and we strongly recommend the use of either of these high 
quality servos. 
 
-Torque 2814T/820 Brushless Outrunner motor. 
 
-Airboss Elite 45 Amp ESC. 
 
-4S 2100-2700 mah LiPo battery.   
 
-APC 12x6 E (NOT the slow fly version!) or XOAR 12x6 electric prop.  
 
-52mm Extreme Flight spinner. 
 
-2 18"-24" extensions for the 2 rear servos and 2 6"-8" extensions to go between the 
receiver and the aileron servo leads.  We recommend the 28 or 32 AWG extensions to save 
weight. 
 
-Adhesive backed Velcro and Velcro strap for battery retention. 
 
 

Содержание YAK-54 EXP




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды