background image

Introduction 

Congratulations on your purchase of the Extech EX470A True RMS Autoranging Multimeter plus IR 

Thermometer. This meter measures AC/DC Voltage,  AC/DC Current, Resistance, Capacitance, 

Frequency, Duty Cycle, Diode Test, and Continuity plus Thermocouple and Non-Contact IR 

Temperature. Proper use and care of this meter will provide many years of reliable service. 

Safet 

International Safety Symbols 

A.

This symbol, adjacent to another symbol or terminal, indicates the user must refer to the

fil 

manual for further 

information. 

/A. 

This symbol, adjacent to a terminal, indicates that, under normal use, hazardous vo

l

tages 

�  may be present 

ID 

Double insulat

i

on 

WARNING 

CAUTION 

r

MAX 

_soov 

-

-

This 

WARNING 

symbol indicates a potentially hazardous s

i

tua

t

ion

which if not 

avoided, could result in death or serious injury. 

This 

CAUTION 

symbol indicates a potent

i

ally hazardous situation, which if not 

avoided, may result damage to the product. 

This symbol advises the user that the terminal(s) so marked must not be 

connected to a circuit point at which the voltage with respect to earth ground 

exceeds (in this case) 600 VAC or VDC. 

This symbol indicates there is a potential hazard from a laser light source

t

AVOID EXPOSURE 

Loser radiation is emitted 

£ 

from this aperture 

CAUTION 

LASER RADIATION-OD NOT STARE INTO BEAM 

OUT1'1JklmW WAVHENGlli 630,670nm 

CLASS 2  LASER PRODUCT 

11160825-1:1994/Al 1: 1996/A2:2001/Al:2002 

EX470A-en-GB_v6.0  6/16 

Содержание EX470A

















Отзывы: