manualshive.com logo in svg

Expleco Oppressor GLC, Инструкция по эксплуатации

Поделиться
Скачать
Expleco Oppressor GLC Скачать руководство пользователя страница 8

 

 
 

                IMPORTANT PLEASE READ BEFORE ASSEMBLY 
 

Chute Refit 
 

•

 

Refit main chute using bolts found in hinges. Make sure 10mm washers are 
reinstalled each side of hinge and 8mm washer is installed between nut and 
10mm washer. 

Filter Refit 
 

•

 

Push filter down firmly so that tube presses on white pre filter disc and tighten 
with a screwdriver. 

 
The user manual has all the information about operating the machine and trouble 
shooting. Below are the key points to stay safe and avoid jams or creating a mess. 
 
If GLS Machine has lever jack please read instruction on 

reverse

 of this sheet. 

 
Key Points 
 

•

 

Never open the machine when it is turned on or plugged in at the wall.  

•

 

Never over fill the GLS bucket or GLC Wheel Bin or use a foreign bucket or 
bin. 

•

 

Never put a bottle in before the machine is turned on. 

•

 

After the last bottle has gone through let it run for a few seconds to clear all 
particles. 

•

 

Never attempt to put in broken glass or clear a jam without using gloves. 

•

 

If you run the machine on an extension cord keep it as short as possible to. 
ensure the machine operates at its most efficient. 10-15m max. 

•

 

Keep the machine indoors. 

•

 

IMPORTANT 

always feed bottles into chute with pressure that 

fires 

bottles 

into chute rather than easing them into chute 

 

Please contact us once you have your machine set up and someone will talk you 
through all the features and finer points of operation to ensure you get the best out of 
your GLS or GLC glass crusher. 
 
I look forward to hearing from you in the near future and wish you all the best in 
reducing your glass waste and improving your business sustainability. 
 
Kindest Regards 
Tim Barnett 

Marketing Manager 

Содержание Oppressor GLC











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды