manualshive.com logo in svg

Exmark ULTRAVAC BAGGER, Инструкции по установке

Поделиться
Скачать
Exmark ULTRAVAC BAGGER Скачать руководство пользователя страница 14

pivot pin (item 21) and hairpin (item 22) may be
stored in the pivot holes on the discharge chute
during bagging operation.

Units Serial Number 600,000 and
Higher:

1. Stop the engine, remove the key, and wait for all

moving parts to stop.

2. Lower the deck fully. Remove the right hand belt

cover. Remove the belt cover mounting stud that
protrudes from the deck. Save the knob for later use.

3. Remove the blade from the right spindle.

4. Insert the special tool 109-2979 into splined end of

the spindle shaft.

5. Remove the right sheave nyloc nut, washer, and

splined washer from the spindle shaft. Do Not
remove the blade drive sheave. Retain the nut for
later use.

Use special tool 109-2979 to hold spindle from
rotating. Do Not use the blade bolt to prevent
rotation.

6. Install the UltraVac drive sheave onto the right

spindle shaft. Install the washer that is supplied with
the UltraVac drive kit (item 47) and the nut removed
in step 5. Torque the sheave nut to: 5/8-18 inch nut
(15/16 Hex) to 90-110 ft-lb (122-149 N-m).

Use special tool 109-2979 to hold spindle from
rotating (see Figure 18). Do Not use the blade
bolt to prevent rotation.

Figure 18

1.

5/8-18 inch Sheave
nut-torque to 90-110 ft-lb
(122-149 N-m)

3.

UltraVac drive sheave
(item 12)

2.

Washer (item 38)

4.

Special tool 109-2979

7. Reinstall blade and torque bolt to:

For units with a 1/2-20 x 2 inch blade bolt,
torque to 50-60 ft-lb (75-81 N-m).

8. Reinstall the deck drive belt in the lower grove of

the double sheave. Install plug (item 40) into bore
of top sheave.

9. Remove the discharge chute from the deck. Discard

the mounting hardware, but save the discharge chute
for use during side discharge operation. The chute
pivot pin (item 21) and hairpin (item 22) may be
stored in the pivot holes on the discharge chute
during bagging operation.

10. Install deflector (item 48) at the front right corner

of deck as shown in Figure 19. Use carriage bolt,
nut and washer that retains right corner of adjustable
front baffle.

Figure 19

11. Install the belt cover mounting stud (item 27).

For 60 inch units only, install the spacer (item 29),
two 7/16 spring disc washers (item 30) and the
plastic knob (see Figure 20). The knob does not
need to be tightened against the washers at this time.

14

 

Содержание ULTRAVAC BAGGER




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды