manualshive.com logo in svg

Exmark Quest 4500-450, Руководство оператора

Поделиться
Скачать
Exmark Quest 4500-450 Скачать руководство пользователя страница 35

Maintenance

Fuel System Maintenance

Replacing the Fuel Filter

Service Interval: Every 100 hours/Yearly

(whichever comes first)

DANGER

In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or
explosion from gasoline can burn you and
others and can damage property.

•

Perform any fuel related maintenance
when the engine is cold. Do this outdoors
in an open area. Wipe up any gasoline
that spills.

•

Never smoke when draining gasoline, and
stay away from an open flame or where a
spark may ignite the gasoline fumes.

Never install a dirty filter if it is removed from the
fuel line.

1. Park the machine on a level surface and disengage

the blade control switch.

2. Move the motion control levers outward to the

neutral position, engage parking brake, stop the
engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

3. The fuel filter is in the fuel line between the tank

and engine.

Figure 27

1.

Fuel tank

6.

Hose clamps

2.

Fuel shut off valve—off

7.

Fuel line to engine

3.

Fuel shut off valve

8.

Filter

4.

Fuel shut off valve—on

9.

Flow direction arrow

5.

Fuel line from tank

4. Turn fuel shut off valve 90° to “off ” position.

5. Squeeze the ends of the hose clamps together and

slide them away from the filter (Figure 27).

6. Remove the filter from the fuel lines.

7. Install a new filter with the flow direction arrow

coming from the fuel tank and pointing to the
engine. Move the hose clamps close to the filter
(Figure 27) to secure it in place.

8. Turn fuel shut off valve back to “on” position.

Electrical System
Maintenance

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related

accessories contain lead and lead

compounds, chemicals known to the State of

California to cause cancer and reproductive

harm. Wash hands after handling.

35

Содержание Quest 4500-450

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды