Exmark Quest 126-7508 Скачать руководство пользователя страница 23

Maintenance

Note:

Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 10 hours

• Inspect the bagger

Before each use or daily

• Clean the bagger

Before storage

• Inspect the bagger
• Clean the bagger

CAUTION

If you leave the key in the ignition switch, someone could accidently start the engine and
seriously injure you or other bystanders.

Remove the key from the ignition and disconnect the wire from the spark plug before you do
any maintenance. Set the wire aside so that it does not accidentally contact the spark plug.

DANGER

The engine can become hot when it is operating. Severe burns can occur from contacting hot
surfaces.

Allow engines, especially the muffler, to cool before touching.

DANGER

Debris, such as leaves, grass, or brush can catch fire. A fire in the engine area can cause
personal injury and property damage.

Keep the engine and muffler area free of debris accumulation.

Take care when opening the bagger cover to keep debris from falling onto the engine and
muffler area.

Allow the machine to cool before storing it.

Inspecting the Bagger
Attachment

Service Interval:

After the first 10 hours

Before storage

Inspect the bagger attachment after the first 10 hours
of operation, and monthly thereafter.

1.

Check the chute, discharge tube, and the bagger
top. Replace these parts if they are cracked or
broken.

2.

Tighten all nuts, bolts, and screws.

3.

Inspect all fasteners and latches; replace any
missing or damaged.

4.

Inspect the grass bags for deterioration.

WARNING

You or bystanders could be severely
injured by flying debris or thrown objects
that may pass through torn, worn, or
deteriorated grass bags.

Check the grass bags for holes, rips,
wear, and other deterioration.

Do not wash the grass bags.

If the bag has deteriorated, install
new grass bags supplied by
the manufacturer of this bagger
attachment.

23

 

Содержание Quest 126-7508





























Отзывы: