background image

Operation

7. Install the belt cover using the two knobs. Install

the discharge tube assembly by slipping the upper
end into the hood, then sliding the lower end over
the blower discharge opening. Use the latches to
retain the lower end to the blower.

8.

For Units 600,000 and Higher with Triton
Decks:

Adjust position of dog leg baffle to match

the intake of the Ultra Vac blower baffle adjusted
too wide may allow objects to be thrown from
under deck. Baffle adjusted too narrow may cause
plugging issues.

For units with a 2 post ROPS installed:

Install

the weight.

Note:

The portions of the Ultra Vac bagger that

are not bolted to the mower are designed to be
installed or removed in their entirety. Do Not
operate the mower with only a portion of the
Ultra Vac installed.

Transporting

Transporting a Unit

Use a heavy-duty trailer or truck to transport the
machine. Lock brake and block wheels. Securely
fasten the machine to the trailer or truck with straps,
chains, cable, or ropes. Be sure that the trailer or truck
has all necessary lighting and marking as required by
law. Secure a trailer with a safety chain.

CAUTION

This unit does not have proper turn
signals, lights, reflective markings, or a
slow moving vehicle emblem. Driving on a
street or roadway without such equipment
is dangerous and can lead to accidents
causing personal injury. Driving on a street
or roadway without such equipment may also
be a violation of State laws and the operator
may be subject to traffic tickets and/or fines.

Do Not drive a unit on a public street or
roadway.

WARNING

Loading a unit on a trailer or truck increases
the possibility of backward tip-over.
Backward tip-over could cause serious injury
or death.

Use extreme caution when operating a
unit on a ramp.

Use only a single, full width ramp; Do
Not use individual ramps for each side
of the unit.

If individual ramps must be used, use
enough ramps to create an unbroken
ramp surface wider than the unit.

Do Not exceed a 15° angle between ramp
and ground or between ramp and trailer
or truck.

Avoid sudden acceleration while driving
unit up a ramp to avoid tipping backward.

Avoid sudden deceleration while backing
unit down a ramp to avoid tipping
backward.

Loading a Unit

Empty grass bags before attempting to load
unit on trailer or truck.

Use extreme caution when

loading units on trailers or trucks. One full width
ramp that is wide enough to extend beyond the rear
tires is recommended instead of individual ramps for
each side of the unit. The lower rear section of the
tractor frame extends back between the rear wheels
and serves as a stop for tipping backward. Having
a full width ramp provides a surface for the frame
members to contact if the unit starts to tip backward.
If it is not possible to use one full width ramp, use
enough individual ramps to simulate a full width
continuous ramp.

Ramp should be long enough so that the angles
between the ramp and the ground and the ramp and
the trailer or truck do not exceed 15°. A steeper angle
may cause mower deck components to get caught as
the unit moves from ramp to trailer or truck. Steeper
angles may also cause the unit to tip backward. If
loading on or near a slope, position the trailer or
truck so it is on the down side of the slope and the
ramp extends up the slope. This will minimize the

14

Содержание LAZER Z HP Series

























Отзывы: