Operation
Important:
Do Not use kerosene or gasoline
instead of diesel fuel. Failure to observe this
caution will damage the engine.
Do Not
overfill fuel tank. Fill the fuel tank to the
bottom of the filler neck. The empty space in the
tank allows the fuel to expand. Overfilling may result
in fuel leakage or damage to the engine or emission
system.
If possible, fill the fuel tank after each use. This will
minimize possible buildup of condensation inside the
fuel tank.
Biodiesel Ready
This machine can also use a biodiesel blended fuel
of up to B20 (20% biodiesel, 80% petrodiesel). The
petrodiesel portion should be low or ultra low sulfur.
Observe the following precautions:
•
The biodiesel portion of the fuel meets
specification ASTM D6751 or EN14214.
•
The blended fuel composition should meet
ASTM D975 or EN590.
•
Painted surfaces may be damaged by biodiesel
blends.
•
Use B5 (biodiesel content of 5%) or lesser blend
in cold weather.
•
Monitor seals, hoses, gaskets in contact with fuel
as they may degrade over time.
•
Fuel filter plugging maybe expected for a time
after converting to biodiesel blends.
•
Contact your distributor if you wish for more
information on biodiesel.
Operating Instructions
Raise the Rollover Protection System
(ROPS)
Important:
Lower the roll bar only when
absolutely necessary.
1. Remove the hairpin cotter pins and remove the
two roll bar pins (Figure 6).
2. Raise the roll bar to the upright position and
install the two pins and secure them with the
hairpin cotter pins (Figure 6).
Important:
Always use the seat belt with the
roll bar in the raised position. Ensure that the
rear part of the seat is secured with the seat
latch.
Figure 6
1.
Roll bar
3.
Pin
2.
Raised position
4.
Hairpin cotter pin
Open the Fuel Shut-Off Valve
Turn the valve to the LH or RH tank.
Starting the Engine
1. Move the motion control levers out to the neutral
lock position.
2. Pull up and back on the parking brake lever to
engage the parking brake.
3. Push down on the PTO switch to the “disengage”
position.
Note:
It is not necessary for the operator to be
in the seat to start the engine.
4. Place the throttle midway between the “SLOW”
and “FAST” positions.
5. On a warm engine, place the throttle in the
“SLOW” position.
6. On a cold engine, (below 14°F (-10°C)), place the
throttle in the “MIDWAY” position.
Note:
Do Not use fuel left over from summer.
23
Содержание LAZER Z D-SERIES Operators
