Exmark Frontrunner Скачать руководство пользователя страница 40

Страница: 40 / 52

Troubleshooting

Problem

Possible Cause

Corrective Action

1. Engine load is excessive

1. Reduce the ground speed.

2. Oil level in the crankcase is low.

2. Add oil to the crankcase.

Engine overheats

3. Cooling fins and air passages for the

engine are plugged.

3. Remove the obstructions from the cooling

fins and air passages.

1. Tracking needs adjustment

1. Adjust the tracking.

2. Tire pressure in drive tires not correct.

2. Adjust tire pressure in the drive tires.

Mower pulls left or right (with levers fully
forward)

3. Reverse indicator and motion control

linkage need adjustment.

3. Adjust the reverse indicator and the

motion control linkage.

1. Bypass valve is not closed tight.

1. Tighten the bypass valve.

2. Drive or pump belt is worn, loose or

broken.

2. Change the belt.

3. Drive or pump belt is off a pulley.

3. Change the belt.

4. Broken or missing idler spring.

4. Replace the spring.

Machine does not drive

5. Hydraulic fluid level is low or too hot.

5. Add hydraulic fluid to reservoir or let it

cool down.

1. Engine mounting bolts are loose.

1. Tighten the engine mounting bolts.

2. Loose engine pulley, idler pulley, or blade

pulley.

2. Tighten the appropriate pulley.

Abnormal vibration

3. Engine pulley is damaged.

3. Contact an Authorized Service Dealer.

1. Fuse is blown.

1. Replace fuse. Check coil resistance,

battery charge, charging system, and
wiring connections and replace if
necessary.

2. Low voltage supply at the clutch.

2. Check coil resistance, battery charge,

charging system, and wiring connections
and replace if necessary.

3. Damaged coil.

3. Replace clutch.

4. Inadequate current supply.

4. Repair or replace clutch lead wire or

electrical system. Clean connector
contacts.

Clutch will not engage.

5. Rotor/armature airgap is too large.

5. Remove shim or replace clutch.

Содержание Frontrunner





















































Результаты поиска

Содержание Frontrunner

Отзывы:

Похожие инструкции для Frontrunner

Бренды по названию

Популярные бренды

Exmark Frontrunner, Руководство оператора

Результаты поиска

Содержание Frontrunner

Отзывы:

Похожие инструкции для Frontrunner

Бренды по названию

Популярные бренды