background image

Maintenance

Service Air Filter
(Kawasaki Units)

Service Interval: Every 25 hours—Clean

the foam pre-cleaner
(Kawasaki Units).

Every 300 hours—
Replace the paper air
filter (Kawasaki Units).
(May need more often in
dusty conditions. See
the Engine manual for
additional information.)

Note:

Do Not

operate the engine without the air

filter assembly; extreme engine damage will occur.

1. Stop engine, wait for all moving parts to stop.

2. Disconnect the wire from the spark plug.

3. Remove the cover and clean it thoroughly.

Figure 23

X-Series Units

1.

Cover

3.

Paper air filter

2.

Foam element

4.

Air filter base

Figure 24

S-Series Units

1.

Cover

3.

Foam element

2.

Paper air filter

4. Remove the paper air filter and discard it as

required.

Note:

Do Not

try to clean a paper air filter.

5. Remove the foam element and wash it with a mild

detergent and water, then blot it dry.

6. Saturate the element with clean engine oil, then

squeeze it (Do Not twist) to remove the excess oil.

7. Install the foam element.

8. Install the new paper air filter.

9. Install the cover.

Service Air Filter
(Honda Unit)

Service Interval: Every 25 hours—Clean

the cover, base, foam and
paper elements (Honda
Unit).

Every 250 hours— Replace
the air filter elements
(Honda Unit). (May need
more often if they are

26

 

Содержание COMMERCIAL 21









































Отзывы: