background image

COLLECTION SYSTEM

142-6386, 142-6387, 142-6388

Setup Instructions

For Bagger Serial Nos. 408,644,346 & Higher

(To fit Quest Units Serial Nos. 408,644,346 & Higher)

Loose Parts

Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.

Dealer Pack

Part No.

Description

Qty.

Use

Bolt (3/8 x 1 inch)

4

Locknut (3/8 inch)

6

Bracket-Mounting, Left weight

1

Bracket-Mounting, Right weight

1

Washer

2

Bolt (5/8 x 2-3/4 inches)

2

Weight-Suitcase

6

Install the weights.

Bracket-Stabilizer

1

Bolt-Carriage (5/16 x 3/4 inch)

2

Locknut (5/16 inch)

4

Self-tapping screw (5/16 x 3/4 inch)

2

Bolt (5/16 x 1 inch)

2

Frame-Pivot

1

Hairpin cotter

2

Rod

2

Washer

2

Install the attachment mount

Latch rod

1

Hairpin cotter

1

Install the latch rod.

Bagger top

1

Bagger screen

1

Assemble the bagger top–All Deck
Sizes.

Grass Bag

2

Upper bagger tube

1

Pivot bracket

2

Bolt (5/16 x 1 inch)

4

Nut (5/16 inch)

4

Install the bagger top.

Chute

1

Baffle (50-inch decks only)

1

Install the chute–All deck sizes.

Attaching the Discharge Tube–All
Deck Sizes

Fill out the online warranty registration
form.

Literature Pack

Manual-Operator's

© 2020—Exmark Mfg. Co., Inc.
415 Industrial Row
Beatrice, NE 68310

Part No. 4505-498 Rev. A

Printed in the Mexico.

All Rights Reserved

*4505-498* A

 

Содержание 142-6386








Отзывы: