background image

Form No. 4501-494 Rev A

Installation Instructions

Mule Drive Damper Retrofit Kit

Kit No. 116-9360

For Serial No. 600,000–312,999,999

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm.

Safety Alert Symbol

This Safety Alert Symbol (Figure 1) is used both in this
instruction sheet and on the machine to identify important
safety messages which must be followed to avoid accidents

This symbol means:

ATTENTION! BECOME ALERT!

YOUR SAFETY IS INVOLVED!

Figure 1

Safety Alert Symbol

The safety alert symbol appears above information which
alerts you to unsafe actions or situations and will be followed
by the word

DANGER

,

WARNING

, or

CAUTION

.

DANGER

: White lettering / Red background. Indicates an

imminently hazardous situation which, if not avoided,

Will

result in death or serious injury.

WARNING

: Black lettering / Orange background. Indicates

a potentially hazardous situation which, if not avoided,

Could

result in death or serious injury.

CAUTION

: Black lettering / Yellow background. Indicates

a potentially hazardous situation which, if not avoided,

May

result in minor or moderate injury.

This manual uses two other words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

WARNING

While maintenance or adjustments are being made,
someone could start the engine. Accidental starting
of the engine could seriously injure you or other
bystanders.

Remove the key from the ignition switch, engage
parking brake, and pull the wire(s) off the spark
plug(s) before you do any maintenance. Also push
the wire(s) aside so it does not accidentally contact
the spark plug(s).

Note:

Determine the left and right sides of the machine

from the normal operating position.

© 2012—Exmark Mfg. Co., Inc.
Industrial Park Box 808
Beatrice, NE 68310

www.Exmark.com

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*4501-494* A

Содержание 116-9360

Страница 1: ... Black lettering Orange background Indicates a potentially hazardous situation which if not avoided Could result in death or serious injury CAUTION Black lettering Yellow background Indicates a potentially hazardous situation which if not avoided May result in minor or moderate injury This manual uses two other words to highlight information Important calls attention to special mechanical informat...

Страница 2: ...6658 Nut Nyloc 3 8 16 Flg 5 3 109 8866 Bushing Plastic 2 11 3231 31 Bolt Carriage 3 8 16 x 2 1 2 2 4 104 8301 Nut Nyloc 3 8 16 Flg 2 12 3231 5 Bolt Carriage 3 8 16 x 1 3 4 1 5 323 12 Screw HH 3 8 16 x 2 1 2 1 13 3231 7 Bolt Carriage 3 8 16 x 2 1 4 1 6 116 6316 Spring Extension 1 14 116 9359 03 Bracket Damper Mnt Upper 1 7 116 0932 Dampener Sleeve 1 15 323 6 Screw HH 3 8 16 x 1 2 8 116 9300 Spacer ...

Страница 3: ...g if in good condition remove and retain otherwise a new pulley and or bushing must be installed Discard all other mule drive components 9 Place the upper dampener mount bracket onto rear face of the engine mount bracket and align as shown in Figure 4 Mark the hole locations and drill two 406 inch diameter holes in the rear face of the engine mount bracket Attach the upper dampener mount bracket u...

Страница 4: ...ive hours Self tensioning idler adjust as follows 1 Stop engine wait for all moving parts to stop and remove key Engage parking brake 2 On the left side of the engine deck support check the location of the bolt head in the center of the spring loaded pulley The top of the bolt should be at the bottom of the upper alignment hole as shown in Figure 6 It is necessary to adjust the belt tension when t...

Отзывы: